As I’ve said before, I am super new to woodworking. As in i haven’t done a woodworking specific project yet, just home improvement type things. So in my quest for tools I decided a Shopsmith would be the best bang for my buck to start out with. After watching Craigslist for a month or so I found a sweet deal on a used Shopsmith with several extra goodies. I wound up paying $675 for everything. It had a little rust, but I’ve taken care of that for the most part (still need to...
Well I guess through learning and creating, sawing and shaving there were a few more hours to conjureup some additional ideas with my chisel box. Ahhh yes…a lid for the top perhaps??.....this would be a total ad lib affair with little more than just letting the inner kid out to explore and experiment. Every now and then that is such a vital important exercise to have in our woodwork…..be free of worries…the crayons going out of the lines are no artistic sin, only stressfu...
Hey!I’m Alexandre, who likes wood.I also like playing adventure video games such as minecraft etc…I do woodworking with my dad, I really like building stuff and my own tools.I came from South Africa and now live in Ontario, Canada.I started woodworking basically immediately after I came, So I came August 2010 and then yeah…The reason I started woodworking was:In South Africa, Wood was EXPENSIVEYou could also basically only get Pine, Red oak, Mahogany and this wood I can̵...
Two months in, progress has been made, but of course, not as fast as I would of liked. Figuring out the motors and drives has been the most difficult part of this project. I have been trying to keep the out of pocket cost as low as I could, and provide the power and control that a sander project of this magnitude needs. I had ordered a 2hp 1ph motor on ebay, but that fell through when the motor was damaged by UPS. Since then, what I stumbled upon was a motor controller that uses 220v ...
We are adding on to our shop! My dad and I have been talking about it for a while and have finally pulling the trigger! Our current shop is 44’ by 36’ (1,584 square feet), and every inch of that space is occupied. Here’s what it looks like right now: We will be adding 12’ to each side and 12’ on the back. It will then be 60’ wide and 56’ long (3,360 square feet). The extra 12’ on each side will be separated by a wall from the middle (large) r...
I recently purchased this old hand plane. I believe it is for making the tounges. Not 100% sure though. Does anyone have any ifo to share? Iron has Butch Sheffield on it and the plane has “W Copeland Warranted” on it. Any year range?
After 30 years of using my trusty Makita 400mm planer, I took the plunge and invested most of my hard-earned box profits from the past year in a new Powermatic 15 inch planer. I found that it was a good day to own a 35 horse Kabota tractor with a pallet forks since this gold beauty comes with 500 pounds of love. Quick lessons: When installing the cast iron wings. Attach the center bolt with the wing upside down and then spin it to attach the other two bolts. Put in the set screws...
Zagreb has a huge flea market in the wastelands on the edge of town out by the garbage mountain !I love flea markets, and this one is one of the best. There is all sorts of new products, from clothes to tools and everything in between, along with a second hand car market plus a massive section of second hand goods. Literally everything can be found there. I get most of my router bits there (new) and I like to get old hand tools there also. There’s also many BBQ type food and drink estab...
And by popular demand here is a quick tour of my new workshop just after the move! Ha!
Have you guys ever seen an ancient drill press like this one? It’s old…fortunately for more accurate work, I have access to a 24” radial floor model. This drill press in the accompanying photos is so heavy that I had to build a screw jack to raise and lower the drilling head for adjusting it on the column. I try to avoid this at all costs; I build risers for the drilling table. I think I’m going to build one of those that clamps to the column if I ...
- My Journey As A Scroll Saw Pattern Designer - 1263 parts
- Extremely Average - 324 parts
- Workshop Development - 94 parts
- A journey into the workshop. - 88 parts
- Daily Update - 87 parts
- Just for Fun... - 82 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- As The Lathe Turns - 73 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1285 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 368 entries
- Ecocandle - 325 entries
- MsDebbieP - 311 entries
- Karson - 301 entries
- Martin Sojka - 297 entries
- William - 255 entries
- Betsy - 221 entries
- mafe - 216 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- shipwright - 168 entries
- PurpLev - 163 entries
- BritBoxmaker - 159 entries
- stefang - 148 entries