LumberJocks

Woodworking blog entries tagged with 'tongue'

  • Advertise with us
View CaptainKlutz's profile

Antique Tool Box #7: Tongue and Groove Wooden Plane indentification

03-13-2018 09:04 PM by CaptainKlutz | 1 comment »

Decided to post next 2 planes as a set as they appear to be matching 3/4 tongue and groove profiles. Marking on ends show same “EPC” that many others show. Also have 3/4” stamps.These both have “DEFOREST” “BIRMINGHAM” mark as well? First some pictures of groove profile:- - Now some pictures of the Tongue profile:- - Appreciate any information you can share to educate me on this plane‚Äôs vintage or value.Thanks fo...

Read this entry »


View ThomasLightle's profile

Oak Storage Bench #4: The Panels

02-16-2016 05:03 AM by ThomasLightle | 0 comments »

Hey! I figured out how to embed videos. Yay! Next step is to create the panels that will fit in the tongue and groove joinery of the frame. I chose 1/2” red oak plywood. That way I would have a 1/4” reveal on the outside and the panels would be flush with the frame on the inside.Some of the techniques I practiced in this session are the following:Cross-cutting veneer plywood with minimal tear-outSetting up a dado blade for cutting rabbetsPreparation of panel stock for stainin...

Read this entry »


View Mosquito's profile

Fun with a Stanley #45 - #3: Tongue and Groove

03-18-2014 12:13 AM by Mosquito | 18 comments »

Using my Stanley #45 plane to cut tongue and groove. For the purpose of this example I am using a couple pieces of pine. I am using the 1/4” Tongue and Groove irons, and have the depth on the tongue iron set as deep as it can go. The Groove depth stop is set to match this depth once the tongue has been cut. The #45 is set up with the short rods as opposed to the long rods. There is nothing stopping a person from using the long rods, I just prefer to use the short ones when I ...

Read this entry »


View twobyfour16's profile

Workbench #6: Skirts & Vises

09-05-2012 02:00 AM by twobyfour16 | 3 comments »

So, the top needed skirts, obviously, so time to laminate again. This time, I used 3 pieces of 1×8 black walnut. This gave me a skirt that is 2 1/4” thick, and 6 3/4” wide – after cleaning up the edges. I glued up enough blanks for the front skirt, two end skirts, and chops for both vises. I did not get very many pictures of this process, as I had plenty of lamination pics earlier….I will say that these skirts were BEEFY! And heavy. So, now I had to figure...

Read this entry »


View Mainiac Matt 's profile (online now)

Father - Daughter Project #5: bread boards are done

05-06-2012 12:38 AM by Mainiac Matt | 7 comments »

Decided to do the groove in the bread boards on the router table with a slot cutter bit And then to do the tounge on the end grain of the top with a rabbet bit. I often find the parallel set up bars used with the machinist vice on my bench top mill come in handy for set ups. They are 1/8” thick, so in this case two of them inserted in the groove with a feeler guage leaf was snug as a bug in a rug. This allowed me to match the rabbet bit height to groove bottom. the resu...

Read this entry »


View GodofBiscuits's profile

Why dimensional lumber is wrong for woodworking

05-29-2011 10:42 PM by GodofBiscuits | 16 comments »

The girlfriend and I have been getting into the gardening spirit lately and planting anything and everything that will grow here in the NorthWest. With not a lot of places to plant things I decided to move to the patio for options, some planter boxes along the edge would do nicely. I scoured Google and Youtube for ideas and was disappointed with the lack of quality box plans or videos but eventually found something along the lines of what we wanted and would not cost a fortune to build. After...

Read this entry »


View CaptainSkully's profile

Darrell Peart's Aurora Sofa Table #4: Table Top

09-08-2009 03:38 AM by CaptainSkully | 3 comments »

As I was waiting for another project to dry, I did a little work on the table top. I had cut it oversized on purpose to take advantage of the wavy figure in the board. I then had to face the difficult decision of how to trim it down for a sofa/foyer table that didn’t stick too far out. I settled on a 14” wide board, which leaves plenty of room for a decent overhand in the front, 2 1/4” legs, and a side apron that doesn’t look like a chubby baby’s leg. I the...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com