Hello. I am now working on the base for my workbench. I have changed some of the design details since my first concept, but not by much. The main difference is that the two legs on the Roubo side of the bench have tenons that will go into the bench top. The base was going to attach to the top the way most trestle bases do with bullet dowels, but then I realized that when I use the leg vise, all the pressure will be placed on the dowels! So I redesigned the front legs so that they have a tenon...
No electrons were harmed during the building of this table. This was great fun and even more affirmation of the time I spent building my workbench. Enjoy the video.
Hello. I have now finished the mortise and tenons for the base and have them all fit. Here are the two base assemblies put together. The assembly closest to view still needs a thin leg installed on its right side. You can see the tenons on top of each assembly which will be going into mortises in the bench top. Here is a view of the leg assemblies from the Roubo side of the bench, with the front legs that will be flush to the bench top side and the tenons that will be mortised into the ...
I started today by gluing up the top. Doh! #1I decided to use Dominos for the project and did not pick the right size so I cut all the way through the case. Fix. I decided to use through Dominos for the project. Actually the shelves are held in by through Dominos and a false dado I created by layering plywood on the outer pieces. Glue and staples hold the second layer on. Left to right = bottom to top of side Case AssemblyAssembly is a snap with the Dominos. They hold the p...
In a recent Blog by Obi, he discussed using a router to cut mortises, and this started up a discussion, in which Don cautioned against getting a Hollow Chisel Mortiser. I think there are good thoughts on both sides of this debate, and I don’t mean to do anything other than offer some more experience about purchasing and using a Mortiser, and other methods of cutting mortises. As in anything, the more money you spend, the better tool you get. If I were buying just what I wanted, not what ...
Was FINALLY able to get back to the shop after 12-13 days! Got a bit more done on the table: Trimmed tenons to fit mortises for the top: Dry fit the top: Cut, trimmed and mitered the apron tenons for the base: Here’s the base dry fit: And, the almost completed table!
cut the tenons oversized, then fit the first half inch or so, then pare back from there. fitting much better than the first two which I tried to cut to exact size. luckily those were the back legs; the front legs fit very nicely she’s coming together! thanks for looking
For all the pictures, please click here. Note: This was supposed to have been posted Saturday the 25th… I wasn’t sure how much time I’d have today to work on the bench so instead of charging ahead with measuring the height of the legs to get ready for installing the top, I decided to do some more mundane tasks. They still are in general preparation for the top, but I just wasn’t planning on doing them first. Before I get going though, I had mentioned yestrday...
I wish I knew more about mushrooms and toadstools; Inkcaps appear from time to time, and rubbery, orange or brown alien things are there in the short grass some mornings and gone a few days later. Wrens are bobbing about outside the window today looking for insects in the bushes, maybe it’s the “flying school” wrens – they’ll be around all winter as they don’t migrate, and in the spring (RSPB website) the males will build several nests and the female will choose the nest she likes best. “W...
The second run of mortises is in the legs. The tenoned rails will surround the juniper panels. Rather than squirt the air after each two holes, I looped a hose clamp around the air gun and trigger and used a nut driver to control it. (Nut driver is resting on the screw for the photo only.) It didn’t take much air to keep the work area clean. It was easier to get a bore – slide – bore – stack flow going when there was no interruption to work the air. The mortis...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries