LumberJocks

Woodworking blog entries tagged with 'tenon'

  • Advertise with us
View Ocelot's profile

Equipping the Shop #5: Tenoning Jig - with add-on digital readout

09-10-2011 07:12 AM by Ocelot | 14 comments »

I had in mind to make a rail and stile sort of thing, with what I think are called box joints in the frame. After I took a whack at using the fence on the table saw to guide some pieces on end to cut the box joint notches, I decided that I really needed a tenoning jig. So, after reading a bit on-line, I ordered a tenoning jig from Rockler. I think you can get the same jig for $20 less from Grizzly, but I didn’t notice that til after I ordered it. To obtain the maximum range...

Read this entry »


View RGtools's profile

Hand tool tips and tricks #8: Waste Removal on a Through Mortise.

03-06-2013 02:07 PM by RGtools | 14 comments »

This one is almost stupid, but it happens to still be helpful. On a through mortise you can center your work on a dog hole and some of the random chips will fall through it rather than get jammed into the bottom, where you will have to extricate them later. And Now…a bonus tip!!! When test fitting a mortise and tenon joint take care not to snag anything important… You have been warned and so have I. Cheers, Ryan

Read this entry »


View RGtools's profile

Occasional Table Class (Hand Tool Build) #22: Cutting the Joinery for Your Table

01-16-2012 03:57 PM by RGtools | 14 comments »

First off since you are working on furniture…clean up your bench. Sweep it off and put the tools away. This may seem odd since you are going to take the tools out again but it’s not, you are going to pound on your work quite a bit during this process. Chips left on your bench get wedged under your work and dent it. Sweep your bench off and keep it clean. I put all my tools away after each joint is made to fit, this speeds things up because you are not fishing for tools you thought...

Read this entry »


View Sawdustonmyshoulder's profile

Loose Tenon Mortising Jig #2: SketchUp Model Drawn

01-24-2011 05:41 AM by Sawdustonmyshoulder | 13 comments »

Well, I finally have the SketchUp drawing started. I still have to put dimensions on the drawings and will need to write the instructions. Just wanted to whet your appetite. Here are a couple of views of the 3D drawing:

Read this entry »


View HungryTermite's profile

Workbench #13: Leg Assemblies Complete

02-01-2012 07:56 AM by HungryTermite | 13 comments »

Now that I know what the actual width of the top will be (23 1/2 inches by the way) I was able to cut the short stretchers that connect the front and back legs: I decided to try to drawbore the legs with 3/8” pegs since the short stretchers will be attached permanently. I had already drilled the holes in the legs so all that was left to do was to mark the location on the tenon so the holes could be drilled. I couldn’t get the stretcher all the way into the mortise for som...

Read this entry »


View sras's profile

Mahogany Kitchen Stool Project #9: Seat backs

02-05-2011 04:45 PM by sras | 13 comments »

Q: What goes slower than my progress on these stools? A: My blog on these stools! I have been making progress. Other projects and Christmas gifts provided distractions. And woodworking is still a hobby and has to wait for when there is time after everything else. I find that I am quite able to let a bigger project like this sit to one side for a few weeks and come back to it when I can. Next up are the seat backs. The last entry covered fitting the top and bottom rail of the seat bac...

Read this entry »


View Ron Aylor's profile

• Fr. Chad's Prie Dieu #9: On the Rail

11-12-2017 05:58 PM by Ron Aylor | 12 comments »

On the Rail –  Having calculated the width of the upper case, I ripped and cut to length the various rails. The front received a drawer rail and bottom rail, the back received a top, bottom, and middle rail. At this point I was still unsure of the design of the raised panels.  So, after squaring the rails …   … I cut a 1/4” x 1/4” groove along the edges of the back stiles and rails.   The groove plane from my tongue and groove set places the groove 3/16” from the face of the board.     ...

Read this entry »


View Rob Bois's profile

Joinery #1: I've got a haunch about these tenons.....

07-12-2010 03:38 PM by Rob Bois | 12 comments »

This is a recent blog post I did covering the haunched tenons for the cabinet doors for a six-leg sideboard I am building. This is actually episode 9 of probably about a dozen, but this one stands well on its own since it covers a common joint for basic but strong cabinet doors. I have traditionally used cope and stick joinery for most of my cabinet doors, but this particular design does not call for any molding detail on the insides of the rails and stiles, so I figured I might as well use...

Read this entry »


View Eric's profile

Step Stool #6: Hand-Chopping a Mortise (with Video)

07-21-2008 04:29 AM by Eric | 12 comments »

After I posted about doing my first hand-cut mortise and tenon, Scott wanted to see how I chopped my mortise. He said, “The only time I tried to chop a mortice I left most of a 1/4” chisel broken off in the wood.” Well, when I read that, I kind of freaked out because I hadn’t considered that I could have broken my blade! But I decided to trust in what I was taught, and to remember that I had, indeed, done one successfully. So I decided to keep at it for my second mortise. ...

Read this entry »


View David's profile

Quarter Size Cherry Quilt Chests #5: Fathers Day! MILLER DOWEL UPDATE

06-18-2007 07:12 AM by David | 11 comments »

Happy Fathers Day to all of my LumberJock buddies, and a belated Happy Mothers Day to all of the Lady Jocks! I am looking forward to using the LumberJock CyberToolShare feature to explore everyone’s shop and check out what goodies you all got for Fathers Day! I had the privilege and pleasure of spending the last two days working in my shop. I made a lot of progress on my cherry quilt chests. I am under a time crunch as these need to be delivered at the end of the month, so it was great...

Read this entry »


« prev 1 2 3 4 5 6 ... 17 next »
166 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com