First time blogging… But, the activity I’m on now seems like a good topic. I’m building two beds. I need to join angle irons to wood for bed rails and center beam re-enforcement. I need to join angle iron to angle iron to form a T beam. Now, I’ve drilled into metal more than a few times… Often I’m disappointed with the results. Knowing that the inside of the bed rails will not be on display, I decided to use it as a learning opportunity and for sk...
I think most of you have seen a lot of these pics on other thread but I’ll post them here for the Blog with more detail. As you know last time I tried to carve my screw by hand, it worked but was slow going. So I built the router jig but have been having trouble dialing it in perfectly. Here is the router jig I made. As you can see its a loose fit which is why I got a lot of chipping in the tips of the thread, I was cutting to deep. This is what happened when I fed my hand car...
Hello. After recieving a few questions about the previous video I realized I may have left out some details about the cutter. So in this video I better explain how to dimension the cutter and pick the steel.
Hello. In the latest video I complete all the work on the Tap my buddy Chris Legendre designed. At this point in the series you should have all the knowledge you need to make wooden nuts of whatever size you want. I begin the video by explaining how to locate the mortise for the blade. I continue by showing the entire process involved in making the blade: shaping, hardening, and tempering. I then cut the mortise for the blade and wedge, fit the wedge, and make the “chip clear outR...
Hello. In Part Three of the Tap and Screw Jig Tutorial series I finish the work on the guide block for the Tap my friend Chris Legendre designed. I start by laying out and cutting the metal plate which is inserted into the guide block to guide the dowel through the Tap. After work on the metal plate is done I attach two wooden blocks to create the clearance for the blade as it exists the Tap. The second video is designed to help those who may be confused about laying out the thread patt...
Hello LJ’s, As noted in the previous post I’m halfway through the milling of my lumber. I’ve set that aside for the weekend when I can run my machines without waking the kids. For now I’m starting to work on the wooden screw for my leg vise. First I thought I would post some of my sketches for my wooden screw plans. Maybe they will be helpful for someone else. Sorry, not as pretty as Mads sketches… Here is what I got done last night. I had already glued...
Hello. I have finally put out the second installment of the tutorial. I had to break up the video into two sections in order to fit it onto youtube. In this part I begin work on the tap by making the guide block my friend Chris Legendre designed. The lumber you want to use for the guide should be a hardwood at least 2” thick. Depending on the size of screw you will be making the block can be 3” – 6” wide. It only needs to be surface on one face and one edge. Then...
Hello. This is a new blog series I am doing. The topic is how to make a tap and screw jig for making large wooden screws. To start I will say that I hope many of the readers find this series useful so they can use the knowledge to make their own screws and nuts for clamps, vises, presses, etc… It took my friend Chris Legendre hours upon hours of research, and the both of us experimenting for months to finally get a functioning tap and screw jig. So my purpose in writing this blog is ...
Hello. In this video I show you how I make wooden nuts for my bench with a tap my friend Chris Legendre and I built. I explain some of the details about the tap and show you how its used and set up. Again like I mentioned in my last blog entry, I will be making a video later showing you how to acually make the tap. https://www.youtube.com/watch?v=cztX3GSPBYM&list=UU6RUw1NtwJL0P9C86W54keg
Up until now I was leveling my insert (also on my TS) with blue painters tape – yeah, ghetto, but it works, cheap, and available. When I made the order with Lee Valley last week, I ordered a pack of 10 capscrews and though I’d try to incorporate the leveling concept on the Incra made table. as I stated in my previous post- If I had to start it over, I’d just order the table top from Incra and be done with it – they are worth their price. however. since I already had...
- My Journey As A Creative Designer - Woodworking and Beyond - 1832 parts
- Extremely Average - 324 parts
- Toy costruction - 131 parts
- A journey into the workshop. - 115 parts
- Workshop Development - 107 parts
- Just for Fun... - 98 parts
- Woodworking on a Half-Shoestring - 91 parts
- Shop stuff - 90 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 82 parts
- Sheila Landry (scrollgirl) - 1857 entries
- dbhost - 455 entries
- frank - 417 entries
- degoose - 398 entries
- Ecocandle - 325 entries
- mafe - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- Dave Rutan - 277 entries
- robscastle - 267 entries
- shipwright - 259 entries
- William - 258 entries
- A Slice of Wood Workshop - 241 entries
- bandit571 - 237 entries
- Betsy - 228 entries
- stefang - 221 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries