This video features a new crosscut sled built for my shop. Inspiration for this sled came form books in my library and countless Internet searches. This is a simple project for the shop that will increase safety, speed and accuracy of crosscuts on the table saw. Construction is simple with a MDF base, maple fences, Incra Miter Bars and T-Track. The plan file is available for download. Hopefully this will inspire a sled for your shop! David STOP BLOCK DETAIL FRONT FENCE DETAIL
Woodworking Accessories Alternatives Inexpensive Aluminum T-Tracks! Getting woodworking accessories in a country that woodworking is not a common hobby – actually there are no woodworkers here just cabinet makers – even the simplest things have to be imported and off course you have to wait for them. Importing things from US by the time they arrive here the price number is doubled and that number is in euro now. Importing from UK is cheaper but not always they h...
so my router table project has come to an end. i got my shipment from Lee Valley today and i am happy to say that everything is completed. first upon getting the 2’ T-track i cut it in half with a jigsaw and a metal cutting blade. then i epoxied the track into place. i used a board of mdf to distribute pressure and my two former table saw wings which are probably around 20 pounds each on top. then i just drilled for and installed the t bolts and put on the knobs. and when the fen...
I had an idea of how to make T-track on the cheap. I shot this video with my phone so it is not the best but you get the idea.
I was looking for a place to store my 3 plastic Feather boards. I though how I nice it would be to have another wall to hang a few more things on. That’s when it hit me! It’s been there all along! My garage door! I had some left over T-Track laying around so I cut it into 2 1/2” lengths drilled a two holes in each of the 3 peices and screwed it to the garage door support. Then just attached the my 3 Feather boards to the track! I seem to be always looking for a better p...
Part of my problem, which I assume all woodworkers have is that there is no such thing as scrap wood….thus the piles of ply and lumber everywhere. This leads me to where I am now, musing over a design or two to aid in my quest for floor space and for that matter to just be able to see my floor! At this point I grow weary of looking at sketchup and would like your thoughts. Picture #1 – the overall design, partly borrowed from the generic A frame you have all seen around, wit...
Well I thought I could have the whole cart knocked out in one day, but you wouldn’t believe how incredibly hard it is to work in a garage full of crap! Well, then again, maybe you have been there and can sympathize. Needless to say I made a lot of dust and made some big wood into smaller pieces today. I will let the photo do the talking because there isn’t much to say: torsion box + 4” wheels = platform. :-) As for design, there have been some changes to account for my st...
I was able to figure out why the piece of plywood was not square to the other piece of the A-frame. It turned out that one of the angled wedges at the bottom was a little long and needed to be trimmed. The plywood was already in place and I didn’t feel like unclamping and lifting it off. I used my dozuki and trimmed a thin line between the wedge and ply and after fishing the sliver out from underneath I was able to pound the sheet down into place. I used a level and a framing square to ...
Continuing this blog on T-tracks, there is nothing that goes to waist, even the most insignificant piece, at a given moment may turn out to be gold. So, the other day I was looking into some drawers and I found a cut-off piece of t-track that I used on my router table. We all use them and most times we cut them to size to fit our dimension, as they are sold in specific lengths. So I was thinking why did I save that small 20cm long piece?And the same night as I was browsing along the wo...
Ok, despite this morning’s drama, I manned up (just kidding, I felt better, if I still felt like that nothing would have been accomplished today) and got something done. At this point some thoughts and opinions on squaring up the A frame and how would I go about measuring the angle to make sure its true 5 degrees from centerline on either side? What I was able to do today was rather surprising. I almost finished, but didn’t know how exactly to get things lined up, so I clamp...
- My Journey As A Scroll Saw Pattern Designer - 1507 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 94 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1531 entries
- frank - 417 entries
- degoose - 394 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- mafe - 252 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 207 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 186 entries
- Rustic - 186 entries
- Chris Davis - 183 entries
- BritBoxmaker - 177 entries
- Smitty_Cabinetshop - 165 entries