How does a dog get the LAST bit of water out of his bowl ? With a half-lap :-) Spent too much time figuring out how to get Hurricane Walter to spew less dust, or—at least—how I could capture the dust he spews. Shroud seemed like the way to go. So …. with leftover plywood from the construction of the ol’ ChupaCaja, I made me a dust collection box. ID is about 8” wide x 8” deep x 8” tall. The joinery is (IS it called this ?) half-lap (...
Let me start by saying that the first part of this blog although posted earlier today, was actually made about a year ago, I just posted it today as a preceding part to the one you’re reading now… tried not to double post and ‘push’ other’s from the blog front page, so I waited half a day between 2 posts, although both were made ready at the same time. to continue the story were I left off, what I found most difficult with setting up the box was the box joints...
Why Square?As a complete novice I was always mystified by the idea of turning rough lumber into square lumber. It was hard to visualize, though I had read many articles. I thought that I would give any of you new to this aspect a glimpse of the process. The value: Start with square lumber = better chance of square project. Plus you don’t have to buy dimensional lumber from THE MAN. The VideoWe shot a little video/ stills of ourselves squaring stock for our kitchen cabinet drawers....
I found a nice 5’ piece of red oak at Home Depot that was a bit odd in hue, having more depth to its grain than what I usually see there. I had visions of turning some square plates, so I snagged it: I really slacked off on pics of this turning. This is the only one: In it, I’ve cut the end from the plank to square it up and remove the chipped edges. Then I cut 2 pieces off as long as the plank was wide (7-1/4”). Then I cut some squares of birch from a leng...
Nothing tells you quicker how sharp your plane blade than taking a swipe across the end grain. It should go without saying that this tip requires a freshly sharpened blade. Come along and learn how I square up the end of a board using only hand tools.
I’ve always wondered why are there sets of squares out there. Isn’t a square a square? aren’t they all the same? Can’t you just have 1 and be done with it since if something is square…well – it’s square, right? A recent check made me realize I probably have more squares than any other tool in my toolbox (excluding chisels and drill bits of course). How did that happen?!? When I first started woodworking, I got myself a 12” square from the ...
Okay so it wasn’t 72 degrees, but it was close. Early March and a 60degree plus day in Rochester, NY, you want to be outside. SO I was. I squared up a round log.Video Log Overview I used my Logosol Timber Jig and a 2×6 rail I built (seen here). Close Up 1 Close Up 2 So now with my circular saw and a hand saw I plan on cutting this 8×8 down to 4×6’s and trying to make sawhorses. BTW: Can anyone name the movie this entry is quoting?
This might seem totally obsessive, but I am an efficiency Nazi in my shop. Wasted movements drive me crazy and any time I can get into a habit that saves me a few seconds it makes me happy. This is of course especially true in the case of repetitive tasks. One such task is marking the layout lines of a board to cut it square. If you have been working with hand tools for even a short time you have probably heard to “Reference only from your true face and true edge”. This is sage wisdom, but...
hand’t got the chance to post this on sunday, but I did get a chance to mill the drawer fronts to thickness, width, and height on sunday, and temporarily install them on the drawers. for lack of materials the drawer fronts came to be 3/8”+ in thickness as opposed to the original plan of 3/4”, but since this is just drawer fronts, I’m not too concern about this. it actually makes it looks a bit more refined and elegant. I do have some alignment issues as the drawe...
I had a Ryobi 14 Amp 10 in. Compound Mitre Saw. It was working fine but could only cut a max of 5 inches wide boards. I was in the market for a new on but all of the sliding miter saw was so costly. I even considered a Harbor Freight one, but even at that it was a $100 and more for one. I decided to check out craigslist.com and found a Kobalt one there for s feel. Well, after I got home I found out why it was so cheap – it was not square. I tried a couple of time to square it up but it...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries