LumberJocks

Woodworking blog entries tagged with 'square'

  • Advertise with us
View NBeener's profile

1956 DeWalt MBF 9" Radial Arm Saw #7: (Less) Dust in the Wind

03-09-2011 01:26 AM by NBeener | 37 comments »

How does a dog get the LAST bit of water out of his bowl ? With a half-lap :-) Spent too much time figuring out how to get Hurricane Walter to spew less dust, or—at least—how I could capture the dust he spews. Shroud seemed like the way to go. So …. with leftover plywood from the construction of the ol’ ChupaCaja, I made me a dust collection box. ID is about 8” wide x 8” deep x 8” tall. The joinery is (IS it called this ?) half-lap (...

Read this entry »


View Dennisgrosen's profile

toolgloat #5: with a little luck....with a little luck.....

02-22-2011 12:12 AM by Dennisgrosen | 37 comments »

... with a little luck….with a little luck…..and some help from my sister, handtools ..... I have over the year always talked about how great and fantastic possibillity it is for you to have acces to fleamarkets and other places where it is possible to buy good used beautyfull handtoolsmore or less rusty but with a little albowe grease and knowledge is going to bee great users again I have envy you alot when I have seen your toolgloats witch has cost mee many green bulbs and...

Read this entry »


View RGtools's profile

Hand tool tips and tricks #14: Layout Speed Tip.

03-29-2013 02:49 AM by RGtools | 16 comments »

This might seem totally obsessive, but I am an efficiency Nazi in my shop. Wasted movements drive me crazy and any time I can get into a habit that saves me a few seconds it makes me happy. This is of course especially true in the case of repetitive tasks. One such task is marking the layout lines of a board to cut it square. If you have been working with hand tools for even a short time you have probably heard to “Reference only from your true face and true edge”. This is sage wisdom, but...

Read this entry »


View gizmodyne's profile

How To #1: Video Blog: Squaring Lumber with Power Tools

05-01-2007 04:58 AM by gizmodyne | 15 comments »

Why Square?As a complete novice I was always mystified by the idea of turning rough lumber into square lumber. It was hard to visualize, though I had read many articles. I thought that I would give any of you new to this aspect a glimpse of the process. The value: Start with square lumber = better chance of square project. Plus you don’t have to buy dimensional lumber from THE MAN. The VideoWe shot a little video/ stills of ourselves squaring stock for our kitchen cabinet drawers....

Read this entry »


View PurpLev's profile

Hand Tools Cabinet #2: Chisels on the Left, Markings on the right

02-07-2009 06:05 AM by PurpLev | 14 comments »

Let me start by saying that the first part of this blog although posted earlier today, was actually made about a year ago, I just posted it today as a preceding part to the one you’re reading now… tried not to double post and ‘push’ other’s from the blog front page, so I waited half a day between 2 posts, although both were made ready at the same time. to continue the story were I left off, what I found most difficult with setting up the box was the box joints...

Read this entry »


View PurpLev's profile

Router Table #11: Drawer Fronts in Front(s) of the Drawers

01-26-2010 05:21 AM by PurpLev | 14 comments »

hand’t got the chance to post this on sunday, but I did get a chance to mill the drawer fronts to thickness, width, and height on sunday, and temporarily install them on the drawers. for lack of materials the drawer fronts came to be 3/8”+ in thickness as opposed to the original plan of 3/4”, but since this is just drawer fronts, I’m not too concern about this. it actually makes it looks a bit more refined and elegant. I do have some alignment issues as the drawe...

Read this entry »


View PurpLev's profile

Woodworker Chronicles #1: Don't be such a ☐

11-13-2011 06:15 AM by PurpLev | 11 comments »

I’ve always wondered why are there sets of squares out there. Isn’t a square a square? aren’t they all the same? Can’t you just have 1 and be done with it since if something is square…well – it’s square, right? A recent check made me realize I probably have more squares than any other tool in my toolbox (excluding chisels and drill bits of course). How did that happen?!? When I first started woodworking, I got myself a 12” square from the ...

Read this entry »


View mafe's profile

Squarerulerbevelangelbandit (yeah right MaFe!) Blog

09-20-2010 12:26 AM by mafe | 10 comments »

SquarerulerbevelangelbanditOr just a old English set square and bevel gauge, becoming a transformer! The story is that I bought this wonderful vintage English engineers tool:And of course I had to go crazy on it! So I cut a steel ruler into 8 cm of length, why 8? Because I wanted to be able to make 1:8 dovetails…And since there were a spur, I made a hole, and then it can also go sideways (even I have to count down from 5,5 if I go from the set square). I also gave it some new ...

Read this entry »


View A Slice of Wood Workshop's profile

Shop Made Square

08-04-2013 03:38 PM by A Slice of Wood Workshop | 8 comments »

I’ve had a hard time drawing lines across some 2×10’s recently. I made my own square out of wood. I don’t know if it will stay true, so this is a test. Please comment if you’ve made an all wooden square and let me know your outcomes. Please subscribe to my YouTube Channel.

Read this entry »


View Eric's profile

My "Starter Set"

01-18-2008 04:27 PM by Eric | 8 comments »

[Taken from my Adventures in Woodworking blog, August 2007] Before heading back to SE Asia, I needed to accumulate the bare minimum tools needed for woodworking by hand. The class I attended at Homestead Heritage recommends 10 tools in particular, and this is where I started: combination square set of chisels strong layout knife combination marking/mortise gauge small dovetail or gent’s saw tenon saw small hammer for joint assembly solid joiner’s mallet smoothing plane...

Read this entry »


1 2 next »
17 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase