I read about the super sled on a few sites. They all seemed wonderful, but somewhat complex.I wondered what a simple one would do for me. I had a piece of 1/2 inch plywood, some 3/4” wide stock, and a few 2×4’s laying around so I thought I’d see what I could do. I cut the 3/4” stock to fit in the channels of the table saw so they were just even with the top. Then, I cut a the plywood 24” x 36”. I put the strips in the groves and ...
We end up making these three or four times a year, so I decided to post about them because there are so many uses for them. Our cut-off boxes end up getting mitered in a few different angles and we fianlly have one for 45 degrees and a seperate for 90. It’s a quite useful and versitile tool, a must have in all shops. Step by step instructions Bulk woodshop supplies
I was able to plane the stock for the shelves yesterday. I glued up a large enough blank for two shelves, then used the fence to cut them parallel. I then used the cross-cut sled to square the other sides. I got to use my Delta new mortiser to make all of the mortises (3 on each side x 4 sides = 12 total). Luckily, they were all 3/8” and had the same offset from the front/back. This meant that with one setup, I could knock them all out. If I had done them with a chisel, ...
Kris Williams of Rocky Blue Woodworks shows us how to cut perfect circles on a band saw including how to make the sled need to do it!
Hi everyone! Just starting out, and already, I’m running out of money :P Thought I’d share this quick tip someone gave me. Never forget that if you have a festool MFT/3, you always have a convenient way of making a sled with scraps in little to no time. Sled is 3/4 mdf, then just use some clamps on the side of the table to get the bottom rail. Upper rail is easy to do with the MFT/3 accessories. From Woodworking From Woodworking Cheers! Looking forward to doing proje...
Everyone, I would like to Apologize with this Post, I have missed a Detail in my Video Editing, and a Fellow Jock has Brought it to my Attention and now i feel Embarrassed about it lol. There is no Audio in the First part of the Video, I would say pretty close to about 25 Seconds to 40 Seconds into the Video there is no Audio, The Scrolling Text at the bottom of the Video indicate the Fast Forwarding of the Video and that DON’T For sure have audio, that was on purpose so I can reduse...
The new sled is almost done and I am much happier with it. As you can see it’s a basic sled. No Schmancy bits but it runs better in the table, has a DIY T-Track and a blade box so, it’s a upgrade. The back fence is 2 pieces of 1×6 laminated together with glue and screws. I cut a slot in this 5/8” wide and 1/4” deep then laminated a piece of cheap 14” ply over it and cut a 1/4” slot in that to make the t-track. It’s a bit crooked at one ...
I had a cut-off sled, but I wasn’t happy with it. it didn’t slide well at all, I wanted a taller rear fence, and I wanted to try to make some t-track to go on it. so, today, I took apart my old one and started planning the new sled. I was able to remove the old runners without breaking them, which is good, and also without ripping apart the decent plywood that was the base, also good. I was able to determine that the left side of the sled was where the poor sliding problem was a...
I had a miter sled, but I didn’t really like it. It was heavy and bulky and, to be honest, not really that well made. So, since I had a few pieces leftover from trimming down the reclaimed counter top for my eventual router table, I decided to make a new one! This time I went in knowing a bit more about what I wanted and how I wanted to make it. The base is construction-grade 1/2” ply. Not the best but it’s what I had. the miter guide / fence pieces are leftover trim from...
- My Journey As A Scroll Saw Pattern Designer - 1197 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- As The Lathe Turns - 67 parts
- Workshop Development - 66 parts
- Sheila Landry (scrollgirl) - 1219 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 332 entries
- Ecocandle - 325 entries
- MsDebbieP - 301 entries
- Martin Sojka - 297 entries
- Karson - 294 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- mafe - 208 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- shipwright - 160 entries
- BritBoxmaker - 159 entries
- stefang - 145 entries