Hey everybody! I was just reading and responding to someones forum topic about shop design, and I remembered that a while ago I downloaded a Sketchup component library that contained models of most of the power equipment you would find in a wood shop. I got it from the downloads/components page of the old Sketchup (pre Google). I don’t remember who did the modeling but they graciously put it up there for anyone to download and use. Here is a couple of screen shots of the stuff thats in...
Hi LumberJocks! I’ve just recently joined LJ after being a long-time reader. Thanks to everyone who participates in the discussions here. Your wisdom and experience is invaluable, and you are are generous to take the time to share. You can check out my page to learn more about me and my shop, but in a nutshell I am a fairly amateur woodworker working to set up my 2-car garage into a functional workshop. We’ll keep 1 car in most of the time, and I need to get set up to build ...
My shop is in our musty 2-car garage, and while the space itself is quite a bit larger than your average 2 car garage, it is awkward due to the fact we park 2 cars in it (with a single garage door), the presence of some structural posts, an ancient and ginormous furnace, water heater, and laundry. Sometimes I drool at the space a new furnace and tankless water heater would afford me, but that’s another discussion for another day… It has taken me 2 years to determine the optimu...
It’s almost warm again here in Ohio. I spent the winter thinking about how to make my shop more productive. While the snow flew and my tools were safely covered in WD40 I spent a lot of time surfing the web, looking at others’ shops, and playing around in Sketchup. After a while I started to notice a few of the tricks that well-laid-out shops use to be more efficient. So, I downloaded a few tool models from 3D-warehouse and took a stab at it myself. I ended up with this: ...
Yesterday I sold my Ridgid (sniff).Goodbye little buddy. But…... I got my new saw delivered and set up too… : ) manuals galoreand wired with a dedicated circuit today. But along with mo tools/mo problems I started feeling another space crunch. My bench is tall so I can’t outfeed onto it without lowering it or raising the saw. I got stressed about it last night and woke up thinking about my shop layout. So I reread a few articles and decided to try a diagonal la...
Well, I finally got out in the shop for the first time in 2013! I covered my tools with tarps to slow the winter rust. It wasn’t too bad. A little surface rust on the tables. Nothing some WD-40, T-9, and paste wax couldn’t handle. I also decided to remove the Rockler router table from my table saw. I could never get the height right. It made it hard to cut accurately.I am still going to use the router table, but build a new dedicated base for it. I upgraded my lighting this wint...
For those who aren’t familiar with P5, it stands for “Proper Planning, Prevents Poor Performance.” I don’t plan much. I want to, but mostly I just jump in with both feet and course correct as I go along. In this case I am hoping to someday build a seperate woodshop. With that in mind, I set up shop in my tiny 1 car garage. A garage built in 1942. 10’ x 20’...I wish! Closer to 10’ x 15’. Plus, the ceiling is less than 8’ high, eliminatin...
My shop is 16×20 which sounds like a decent size except only about half is usable for woodworking, the other half is storage, lumber, etc. Here is how I started the week. This is where I’m at. This is where I think I want to be. Anything outside the shop (except A/C) are things I don’t have a place for. Anything in dashed lines doesn’t exist yet but I might build. The red line is where I have electric, eventually it will run to the back half but at the ...
I used to do the baby food and mayo jars with the lids nailed under the shelf thing.But after I joined the Navy I had to go more mobile.I started putting my screws and nails into Gatorade bottles.The nice thing is I can put a piece of bailing wire around the neck with a loop on it and hang it on a pegboard.Since the bottle is clear I can see at a glance what’s in it.Right now I don’t have a pegboard wall, but the filing cabinets (another blog entry) work pretty good for keeping th...
- My Journey As A Scroll Saw Pattern Designer - 1598 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1623 entries
- frank - 417 entries
- degoose - 397 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 279 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 218 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 187 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries