A kind LJ frequenting the HPOYD thread noticed a question I asked about spokeshaves, and was nice enough to send an old one my way for about the cost of shipping only. Thank you again, kind sir. Here’s how it looked right out of the box. No maker’s marks or model numbers, but sturdy enough from the look of it. A little bit of surface rust. Nothing too gnarly. The screw for the lever cap is slightly bent, but it still turns alright. Couldn’t find a thumbscre...
Just a quick post for you guys out there with a lathe. Since posting my saw sharpening video in Saw Talk #28, I’ve had a few enquiries about the saw file handles I use. I get them from an online retailer here in the UK and as far as I know they aren’t available anywhere else. That means that if you don’t live in the UK, shipping can be a bit prohibitive. So here are the dimensions (in millimetres I’m afraid) for anyone who is handy with a lathe. They are are a ̵...
My father has been wanting a block plane for a while and had been dropping hints. So I went out on e-bay and found one that was in decent shape. After testing it out it and determining it was worth the trouble, I went ahead and refinished it. Here is what I started with First I lapped the sole and the sides, then I soaked it in Evapo-Rust, then I used a paint stripper to remove the remaining Japanning. I had to use a small piece of 220 grit sand paper to clean up the finger indentations...
My father gave me a wooden plane inherited from my grandpa’s stuff. I think it’s meant to be a scrub or jack plane: the mouth is pretty wide (about 4mm effective, the opening in the body itself being 10-11mm), and the edge is strongly cambered (the corners are 1.5mm back from the center of the camber, over a 54mm wide iron). For perspective, the body is 270mm long, 70mm high, and 73-74mm wide. It’s in pretty good condition but some work is needed to get it back to wor...
Here is the link to a new video I shot of my personal Sopwith Camel Whirligig in action! http://www.youtube.com/watch?v=_bFxcTDEegU
Using Oil Stones Again, Water Stones Now Stowed Away Ollie gave an excellent review of Norton Water Stones and I posted most of the comments below at that review. I think perhaps it was a bit out of place there and offer my apologies to Ollie. I just wanted to present some of my experiences with water stones out in public in case there are others out there that are getting a bit disillusioned with using them. I’ll preface this with, “the vast majority of woodworkers will disagree with...
I found this site while perusing a survival site. There is some good ancient information here. Enjoy! http://journeytoforever.org/farm_library/device/devices2.html
Starts down in the Dungeon Shop. I have a belt sander set up in a vise. And a pair of block plane irons to work over. This is how they looked when they came back from the Dungeon Shop. Backs were flat… and the makings of a decent 25 degree bevel for the edge. Next up, the first of three oil stones… A cheap, little Buck Brothers from Home depot last year. Two grits, don’t remember what they were. Gave it an oil bath, and worked both irons on both side...
Latest Update.The Woodorking Show people have given us a booth at the WoodWorking Show at the Sacramento Convention Center on Nov 13, 14, & 15. They also will tell our story in their press release and other print hand-out. They have made us another offer. FREE TICKETS, but with a condition. They will give us a free ticket for each person that works in our booth. I am passing that offer to LumberJocks. I will need each reciepient to agree to spend a minimum of 1 hour in the boo...
!!!!!!!!!!!!!!!!!!!!!!!!!!!!DISCLAIMER: This article is based on personal experience and preference. I am not responsible for absolutely any personal damage, monetary loss or any “bad happenings” that came/come about through the outcome of this article. By reading this article you 100% agree to the terms of the previous statements. Again I am 100% NOT responsible for any bad mishaps that come about!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Thank you Almost all woodworkers ...
- My Journey As A Scroll Saw Pattern Designer - 1198 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Workshop Development - 67 parts
- As The Lathe Turns - 67 parts
- Sheila Landry (scrollgirl) - 1220 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 333 entries
- Ecocandle - 325 entries
- MsDebbieP - 301 entries
- Martin Sojka - 297 entries
- Karson - 294 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- mafe - 208 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- shipwright - 160 entries
- BritBoxmaker - 159 entries
- stefang - 145 entries