MaFeBurnisher BLOGscraper set up tool Ok I posted the project, and here are the blog, since there seems to be some wishes for that now… If there are wishes, I’ll make a work drawing with measures, but I think it’s quite ‘out the road’.(And thank you, I’m better today, so I could spend a little quality time in the work shop 2×40 min.). The project comes from different ideas I have seen around, and the fact I’m not all happy for my VERITAS...
Bowling Alley Workbench #6: There is more than 1 way to skin a cat - not so with bowling alley floors though - finally success
Yes. Finally some light at the end of the tunnel, reverse thinking, and this project seems a bit more doable, and even not much trouble at all. Originally I tried to get the (2.5” hardened) nails out by using a cat’s paw and a hammer to pull each nail out of the 2.5 laminated hard-rock maple strips. I figured once I get all the nails out of the top strip, it’ll just free it from the lamination, and be nails free… one strip at a time, until I have them all cleared ou...
so After setting on the last design (see previous post in this series) I went out to disassemble the bowling alley laminated top – the purpose was to remove all the nails, so that I can drill the dog holes, and also laminate it in a double stack to give me a 4” top on the perimeter (5” in from the edges – for clamping purposes, and leg attachments). This idea turned to be disastrous. The nails are hardened steel, and twisted making the job of pulling them outridicul...
Chip carving quilt squares, lesson 1 I have a couple of items to cover before we get started with the first lesson. How many quilt squares should I complete?This is completely up to you! I hope that everyone will be able to complete one square to send to me for our LumberJocks Class Quilt. If you would like to send me more, that would be fantastic. How many quilts will we make?I will assemble as many chip carved quilts as possible depending on how many squares you send me. From the l...
Scraper shaves my wayat the end it’s an iron… A iron is what it is all about! So here we are.A scraper has only a value if it can scrape.At the end it’s a iron, a iron attached to a comfortable handle, a tool, the stone age man, the cave man, working, working with the wood, trying to do, to do better, better than last! Why? It’s a call, the call of the caveman who painted those wonderful paintings in colors of the earth on the walls in his cave, now refined from ...
Someone asked me to post this video on this site, so here we go. It is my idea of how to sharpen a cabinet scraper. If I am all wet, please let me know.
Scraper shaves my waymaking a bunch of scraper shaves Lately I have been making quite a few new handles for old hammers and axes, and the finish has been made with a card scraper.This tool, the scraper starts to show its face to me more and more – when a large burr it can produce shavings, and with a fine burr it can make dust. But most of all it brings a finish that you can never get with sandpaper, it brings out the life of the wood. So when I lately saw several people here on L...
Scraper shaves my waywhen the going gets tough… Part three of the tour! Even you disturb me Swirt! Yes you! I just got the ‘Motel of the mysteries’ and I love this book! Have you ever wondered how an archeologist figures out what the artifacts he or she discovers are, and how they were used those many centuries ago? David Macaulay has written an explanation that will inform all of us. He imagines that in 4022, a mediocre amateur archeologist fell into a sink hole wh...
Scraper shaves my waySpin the wheel… Last time we left the scraper shaves in oil!This time we will give them finish and set them up, and then the journey will be at its end… This is my favorite finish tour.From left:Sisal wheel, this helps to clean up and empty for dirt and dust in the cracks and holes, it should actually be used before the oil.Next is compound with a high grid so this added to the wheel gives a finish that is extremely fine, I have two wheels, one for dark ...
Yesterday I got a little adventurous, threw caution to the wind and instead of buying some tools, I made my own. I first made a cabinet scraper. I had to clean up the metal a little. After I got the metal almost all nice and shiny I had to make an edge on one side. I slapped a file in a vise and slid the scraper along it laying down. You have to make sure that the scraper to the file is 90° so the it creates burrs on both sides. This is how the scraper works. I got some little shavings while ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries