108 days ago
by degoose |
28 comments »
Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed.
Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...
Read this entry »
641 days ago
by YorkshireStewart |
37 comments »
I’ve had a fancy for a thicknessing sander but a 10-20 inch model costs the equivalent of $1000 US over here and there’s no way I can justify that sort of spending so I looked into making one of my own. There’s no shortage of help to be had on the world-wide-web. The links I found useful include:
Dominic’s Woodshop
Kawika Ukulele Sander
Ray Lanham Woodcentral
Roberto-Venn School of Luthiery
Mother earth
The Woodshop
Art Herrick
Luthiers’ Friend
Nick’s drum S...
Read this entry »
173 days ago
by scrappy |
29 comments »
Well, I was asked to put together a blog on how I made my segmentd ring. Since I had to make a new one for myself, (first one too small) I thought I would go ahead and do a step by step picture tutorial. My first time ever doing something like this , so hope it comes out OK.
Here goes;
Wood Selection
The first step in making the ring is deciding what woods to use. As we all know, the selection is quite large. One of the most important things is color, but the most important is hardne...
Read this entry »
585 days ago
by Greg Wurst |
16 comments »
Awhile back Wood Magazine had an article on building a mobile outfeed table that would fit over your table saw. Since I need all the space in my garage I can get, I went ahead and built one that would fit over my table saw to give me some much needed work space and a handy outfeed table.
I thought this was pretty spiffy and a great use of space. As I always do I look at the latest project posts on Lumberjocks looking for inspiration for my next project. Whilst browsing I came ac...
Read this entry »
158 days ago
by Andy |
13 comments »
Now that everyone has their wood selected,lets get started.
Note. There will not be your typical cut list of material sizes when making this box.We will cut the box body and a dado for the bottom.The size of the bottom will be measured off of that.
We will then route out for the lid and its size will be determined from that.
Lastly, we will route the recess for the medallion and we will get our final measurement from that.
Note:Depending on your skill level and how clear my instru...
Read this entry »
157 days ago
by Andy |
17 comments »
We now have our box body assembled and glued up.Take off the tape and clean off any dried glue.This is a good time to smooth up the bottom to get rid of any rocking.You can double stick sandpaper onto a very flat and firm surface and slide the bottom across that.The problem with this approach is that sheet sandpaper is way too small.You can stick down several sheets and if you go very slow you may not tear the paper.
Tip:I designed this sanding platform for leveling boxes and flushing out ...
Read this entry »
162 days ago
by Andy |
9 comments »
Let the fun begin!
I know everyone is hoping I will just shut up and just get down to the cutting and sanding :)
BUT…..This is very important to those of you who are trying to imitate my process from beginning to end.Many of you have admitted that you have never built a box before and would like to know how to select a winning combination.So,the first bit of business is to select the wood you will be using.This decision will be based on A) what you find appealing.This is totally s...
Read this entry »
8 days ago
by degoose |
28 comments »
This project is not technically finished so I will not post as a project..This part of the blog will deal with the cutting of arcs.I basically used one of the patron jigs I developed to cut the end curves for a Baguette Board…this pivots on the circle cutting jig. Cut two lengths of contrasting or complimentary timbers… I of course chose Purple Heart and Silver Ash…Silver Ash and Tasmanian Blackwood would have also been suitable… But if all you have is Walnut and Curl...
Read this entry »
157 days ago
by scrappy |
11 comments »
I have been asked to do a tutorial on how I made my Box Joint Bracelet
I will be trying to go Step-By-Step and not leave anything out. I know I am missing a couple of pics but will try and explain things as good as I can.
The first thing I would like to address is SAFETY There are many ways to do almost any process, depending on how you were taught/learned. Please be VERY carfull when useing your tools. I would hate to see anyone get hurt.
Onward: I only used one piece of wood f...
Read this entry »
149 days ago
by Andy |
15 comments »
Three lid choices.
DO NOT CUT THE LID TO SIZE UNTIL YOU ARE SURE OF THE STYLE OF BOX YOU WANT TO MAKE!
At the start of this tutorial I mentioned that we would look at three ways to make this box.
We are at a point in the project,where we need to decide how we want our lid to open.You will need to look at each type and decide which is your favorite or the easiest for you to make.
I suggest following on with this tutorial and weighing the pros and cons of construction,before making a f...
Read this entry »
1 2 3 4 ... 22
216 entries
