LumberJocks

Woodworking blog entries tagged with 'rosewood'

  • Advertise with us
View Woodhacker's profile

Hand Cut Double Dovetail Experiment

2118 days ago by Woodhacker | 74 comments »

After admiring the double and double-double dovetail joints that are capable with the Incra and other jigs, I started thinking, “Why not try this by hand?” So this box is my first experiment with handcut double dovetails. It took me some time to figure out the joinery process, but once I realized a few things about this type of joint, it seemed do-able. It was quite challenging but also a ton of fun. It also does take some degree of patience and precision…which I’m still working on. In...

Read this entry »


View Woodhacker's profile

Houndstooth Dovetails

1967 days ago by Woodhacker | 27 comments »

Houndstooth dovetails use varying sizes of tails (or varying sizes of pins…depending on your perspective). I’ve wanted to try them for quite a while now. This blog shows most of the process I’m currently going through. To get the effect it seems to me you need more tails/pins per corner than one would normally think about. In this case like a few of my other recent boxes posted, I’m using Caribbean rosewood and curly maple. Most often, (when you see them at all) these are done by alte...

Read this entry »


View Lee A. Jesberger's profile

Demilune table tops #1: Making Demilune Tables

2468 days ago by Lee A. Jesberger | 27 comments »

As you may have guessed, I make many of these tables. The practice is needed, and the combinations of woods make it very interesting. These were all made from the plexiglass templates shown. By using these templates, I can make these tops very quickly. I also have other shapes that are more complicated, which I’ll post at another time. Lee

Read this entry »


View degoose's profile

Don't you love surprises????

1561 days ago by degoose | 26 comments »

I got home from work this afternoon with a lot of things to do… I had been down to the Mechanics to see if the old black ute had arrived from the panel beaters..Not yet.. tomorrow… Its a 1962 Ford Falcon… full bare metal respray… all the mechanical and rubbers and suspension and brakes and interior have been replaced or reconditioned.. and new badges….will post pics if you want when I get it back…. picked up some XXXX Gold coolaid and checked My emails̷...

Read this entry »


View BarryW's profile

Wood Source: Is your wood legal?

968 days ago by BarryW | 23 comments »

I found an article today on the internet how Gibson Guitars was raided by the DOJ. I thought maybe it was illegal workers, income tax, something other than what the article was about. Illegal wood. It was a complete shock for me. If they are raiding guitar makers….and to raid Gibson you know it’s a show raid to make as much publicity as possible….then it won’t be long when woodworkers are going to have to prove where the wood they use for projects will have to b...

Read this entry »


View degoose's profile

Torque Workcentre at work.. #15: Cutting rings for bases.

1564 days ago by degoose | 20 comments »

For the last few days at the end of last year ….LOL…I was very busy… I was designing a recessed base for my Lazy Larrys..I have just taken the time to post this….To start I have cut a circle of 5/8” plywood to mount the bearing.. this is roughly 300 mm or 12” in diameter as seen to the left in the first pic.This is accomplished by using the router to drill a hole in the centre.. the same size as the pin in the table. The hole is dropped over the pin and th...

Read this entry »


View BritBoxmaker's profile

Celtic NOT - a journey

850 days ago by BritBoxmaker | 19 comments »

This is the blog of how I built Celtic NOT. The design is one of a recent series of overlapping circle designs. Originally there were two possible patterns These are the original paper models. As you can see the more complicated of the two had an interwoven line on the sides of the box as well. I eventually decided this pattern looked a bit too busy and opted for the simpler of the two. The box was going to be Oak with Sycamore and Walnut stringing. I initially tried making t...

Read this entry »


View Woodhacker's profile

Radial Dovetail Box Construction

2010 days ago by Woodhacker | 16 comments »

Some time ago I posted a blog about a dovetail joint I came up with. I call it the radial dovetail. It incorporates handcut dovetails, but rather than using the traditional 1:8 ratio for the dovetail angle for hardwood, each side of each tail varies and is drawn from a perspective point. Then the sides of the box were contoured to blend with the dovetail design. Here’s a picture of the nearly completed box. It is made of curly maple, Carribean rosewood, and hickory.I like to think of t...

Read this entry »


View Woodhacker's profile

Segmented Bowl - 1st try

1821 days ago by Woodhacker | 15 comments »

Until recently my lathe experience has been 50 or so pen/pencils, a few miniature goblets, and a couple small 5 inch bowls over the past few years on a Jet mini lathe, enough to want to try other lathe work. This past fall I was fortunate to have the opportunity to acquire a PM 3520B, but due to other work and priorities I’ve not had a lot of time to use it yet…and that’s “killing me”. So this blog documents what I consider my first significant lathe project. Recently a partially segmen...

Read this entry »


View Dilo Marcio Fernandino's profile

Chest of Drawers - Work in Progress (50%)

1719 days ago by Dilo Marcio Fernandino | 15 comments »

Dear fellow jocks, I want to report to you all the “odd” woodcarving methods (with photos) that I have been using in the completion of the announced chest of drawers. So, please, click here.

Read this entry »


1 2 3 4 5 next »
45 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase