Here is a video about an easy way to make Tenons on a Radial Arm Saw. This is part of my “Opposing Arch Table” that I am currently working on. (Its 7.5 minutes long) Enjoy!
this is a jig i made years ago, it devides any angle for miters .the circles have mesh teeth that rotate both sides together .i originaly used sand paper , but it wore out quick , and the circles slide singularly .i found some rubber “v” grooved mat , and glued it to the sides of the circles so they mesh , ( it’s not the best , but it works for now )i had to re-cut parts for this new improvement , as there wasn’t room for the mat . it is registered to the table with d...
A tour of the workshop, shop layout, machine set ups, storage ideas. Ljockers enjoy checking out other shops. Hope you enjoy. http://www.youtube.com/watch?v=9GryJsOD8ds
this is a jig to do dados on the RAS .the object , is to make accurate and repeatable cuts for shelving and whatnot .and not cut the saw table or the backstop .as with all of my RAS jigs , they must do these things ,and leave the table , backstop and arm at 90deg. ,so it does not get out of alignment ..this first pic. shows the crosscut dado ..this pic. is the grove with shelf ( imagine ) the depth of cut is regulated by raising or lowering the arm , and this jig has its own stop , that can b...
I’m a BONEHEAD.I like my Dado blades.But they have their limitations.Especially pulling the blade through on your radial arm saw.Ripping a 3/4 inch dado 1 inch deep in a piece of hardwood tougher than oak (I have mallets made from this stuff) exceeds their abilityWhen you try anyway the chippers decide to group together in a show of rebellion and the teeth get mad enough to fly off the handle…er…blade. I knew better.I was in a rush.The fix was $75 at saw stop getting new ...
Well, at least it wasn’t me that bought it this time.I made a gavel and striker on commission from some of the Indian Dontknow I use for a lot of my projects (post on that to follow).I had emailed the customer to let them know they could pick it up.I told the wife they would come over the weekend and she said “You should make a case for it.” I told her that would be more cost, and I haven’t done a case before so it would take about, oh, a year for me to get it figured ...
This saw was my dad’s pride and joy. It a B&D DeWalt R1350 built in 1968. The family gave it and many other woodworking tools to me when he died several years ago. I tuned it up and put a simple table on it back then (2009.) I reassembled and built wheels on the stand. Some say don’t use WD40 – use liquid graffite. After I got all done, I read another book the said, never use liquid graffite – ONLY use WD40. The sign “2nd table” I scraped...
Today I found (on craigslist) a free Craftsman Radial Arm saw. It’s the electronic kind with a digital readout for height/bevel/angle (not sure if I’ll trust it) and it was in very good shape. It needs a new table and fence (don’t they all?!) and some lubrication but the blade is nice and sharp and it’s not rusty or thrashed. I’ve seen people selling these for $75 that were beat up and rusty with missing parts. Best of all, I remembered something from a few ye...
I will show a few pictures of the new coiled wire I added. To attach it I took one of the dual wire holders under the swing arm that was only being used by one wire and swapped it with the one on the column side that was a single wire clamp. Very clean look. The below photos show, I had to get a little creative. Since the new wire coiled cord was larger, I had to get a new wire bushing and modify it, however this coiled cord is heavier and I didn’t want it to stress or pull on...
I found this little gem on craigslist, came with stand 70 bucks, called the ,guy picked it up the same day,This is only a 20 min. drive one wayAlthough it was a little rough getting their, here is what happened. I don’t use my trailer much, so I had to get it out (well it lives outside) get ready to go, I couldn’t get the lights working right, they get corroded setting outside, and had to be replaced every so often. Sooo !!!I grabbed a coupon from harbor freight for some stick on ma...
- My Journey As A Scroll Saw Pattern Designer - 1196 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- As The Lathe Turns - 67 parts
- Workshop Development - 66 parts
- Sheila Landry (scrollgirl) - 1218 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 332 entries
- Ecocandle - 325 entries
- MsDebbieP - 301 entries
- Martin Sojka - 297 entries
- Karson - 294 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- mafe - 207 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- shipwright - 160 entries
- BritBoxmaker - 159 entries
- stefang - 145 entries