Oak leaves have a unique and distinctive leaf shape Oak trees grow on each of the five continents and cultures at every level have relied on the wood and acorn, the tannic acid and the bark throughout the millennia. Great ships with oak bows and rudders crisscrossed the globe. Massive barns and manorial homes came from the stems and crooks of full-grown oaks in every county. It would be impossible to catalogue the provision we have from the ancestry of the common oak. Oak works...
I waxed the dressers with Howards Walnut wax and #0000 steel wool. I tested the difference between sanding with a 1500 grit sanding sponge, and waxing with steel wool – and I prefered the latter. I waxed with the grain, and let the wax dry. Then I buffed it off with a clean lint-free rag. ----- For drawer pull layout I used Scott Collins no-math layout method. My drawer pulls have 2 bolts, 3” on center. -----I made a full-height jig to drill the holes for the machine bo...
I cut the plywood backs to size, and checked the fit. Shiplap backs are nice when they are visible, however the strength of plywood is undeniable. The plywood back fits into a rabbet in the rear leg. The side panels feature floating panels. They are glued only at the center to allow some wood movement. While gluing the side panels, I centered the wood panel for an even reveal on all sides. I cut 1/4” deep dados into the 1/2” plywood back. These dados will lo...
Arts and Crafts Entertainment Center / Sideboard #5: Wedge and Strap Backsplash, Trimming Top, and Staining
So this is where we left off with things last time…-----The entertainment center features a wedge and strap backsplash to match my 6 drawer dressers http://lumberjocks.com/projects/79208 -----Basically it is a shallow dado that receives a walnut inlay. I cut tapers on the backsplash first, then glued the wedges back on. I carpet-taped a strip of plywood to the backsplash to give me a straight reference edge to cut the dados (note to self: rip plywood strip before installing dado bla...
I started the dresser like I start most of my projects, by laminating up some legs. I am making two dressers, so 8 legs were in order. I cut strips of 3/4” quartersawn red oak, and resawed a few of them. I could then glue 3 pieces together to get my leg width. Finally, I glued on 1/4” thick stock to cover my jointlines. After the glue dries, I plane the thickness of these veneers to about 3/32”. That way, I get quartersawn grain on all 4 sides. I then milled s...
Here is the plan from my design. It incorporates some Stickley design elements. --The dresser carcases are assembled, including the small divider that separates the top two drawers.--The small dividers are attached with biscuits. To cut the slots, I opened the top two web frames like a clamshell. The web frames were aligned, and clamped together. Then I added an Emerson straightedge clamp, positioned to center the small divider on the web frame. --The ruler on the Emerson clamp helps cen...
I spent some time card scraping and sanding the 1/2” thick panels for the dresser sides. I sharpened a fresh burr on the card scraper so it was cutting quickly. I use it on trouble spots, like tearout from the planer. I setup the tablesaw with a dado set and a sacrificial fence to cut the rabbets on the panels. They are rabbeted on the inside edge, which will produce a flat panel look on the outside of the dresser. I could have used plywood, but it can be tough to find quartersawn ...
After mounting the slides, I used carpet tape to temporarily attach the drawer fronts. Slides are Centerline 757’s, and mounting is the same as my dresser project here… http://lumberjocks.com/pintodeluxe/blog/34281 -----Drawer fronts installed with 4 screws each.-----Since the drawers are graduated from 6” to 9”, I made a full sized pattern for the largest drawer. Then I marked the size of the other drawers, and used those lines to lay out all drawer pull holes o...
- My Journey As A Creative Designer - Woodworking and Beyond - 1736 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 98 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 78 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1761 entries
- frank - 417 entries
- dbhost - 410 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 303 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 239 entries
- Betsy - 228 entries
- robscastle - 216 entries
- stefang - 215 entries
- Stevinmarin - 212 entries
- Dave Rutan - 210 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- Rustic - 190 entries