LumberJocks

Woodworking blog entries tagged with 'quarter'

  • Advertise with us
View CaptainSkully's profile

Arts & Crafts Dining Room Set #15: He's Got Legs...

1629 days ago by CaptainSkully | 12 comments »

Today, I bit the bullet and tried out my 45 degree lock-miter bit to make the four-sided quarter-sawn white oak 4” x 4” legs. I outsmarted myself by trimming the edges at 45 degrees. Unbeknownst to me, the router bit needs all the meat it can grab to make the “tongues”. As a result, I have very little “lock” in my lock-miter. I have just enough to register the corner, but I’ve lost about half of my glue surface. Sigh… The good news is that...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #14: The Paradox of Quartersawn on Four Sides...

1630 days ago by CaptainSkully | 3 comments »

I ran over to the lumber yard and picked up some 4/4 for the base and a stick of 8/4 to make a single chair out of. I was going to finish the base before I started on the legs, but this 8/4 stick was magnificent (and I didn’t want anyone else to nab it). I recently posted a question in the Design Forum about possibly laminating 3/4” stock to make the legs 1-1/2”, but I couldn’t take any shortcuts (regardless of how cost-effective they might be) on the dining room set...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Night Stands #5: Dry Fit!

1770 days ago by CaptainSkully | 2 comments »

I was able to plane the stock for the shelves yesterday. I glued up a large enough blank for two shelves, then used the fence to cut them parallel. I then used the cross-cut sled to square the other sides. I got to use my Delta new mortiser to make all of the mortises (3 on each side x 4 sides = 12 total). Luckily, they were all 3/8” and had the same offset from the front/back. This meant that with one setup, I could knock them all out. If I had done them with a chisel, ...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #6: The Hard Part

1778 days ago by CaptainSkully | 3 comments »

So, today I ran over to Plywood & Lumber Sales in Oakland, CA and purchased about 100 board feet of quartersawn white oak. I finally have enough lumber to do the dining table. I’m going to start with the top and get that finished so I can bring it into the dining room and set it on top of my old table. This will get rid of the MDF table top we’ve been using for months. It’ll also let me use the MDF for more important things like jigs. I also abhor the tablecloth we&...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #7: Fumearama

1778 days ago by CaptainSkully | 9 comments »

After letting the glue cure overnight, I took it out of the clamps and gave it a final hand sanding. Not too bad, but could be better. I think next time I’ll err on making the legs touch on the outside corners instead of a flat meeting. This caused some gappage that I filled with putty. Since our dog laid down by the tent, I figured it was time to fume. There’s no better time than the present. I carefully put the tent over the table and then propped them both up en...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Night Stands #3: Some Assembly Required...

1792 days ago by CaptainSkully | 4 comments »

Today, I took the rough parts and managed to achieve a few dry fits. The first one was to make sure the dadoes and tenons fit. The second one was to see how it looked with the bow cut out of the bottom piece and with the pre-finished panels installed. A couple of thoughts: be sure your table saw is waxed properly when cutting tenons like this. It helps if you don’t have to use force to push the piece through the saw. I realized I’m already using some of the stuff I learne...

Read this entry »


View CaptainSkully's profile

Stickley Sideboard #1: Selecting the Plans

1809 days ago by CaptainSkully | 9 comments »

At first, I was enamored with #802, as done so well by Dale I looked it up in Robert Lang’s book “Shop Drawings for Craftsman Furniture”. I found an article on building it in Woodworking Magazine, Summer 2009 edition. I felt like I had done my homework and thought I might slip this in between the dining table and the chairs. We already have decent chairs. I didn’t really realize it until I saw Stickley Sideboard #818 at the Arts & Crafts Fair in San Fr...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #4: Change of Plans?

1809 days ago by CaptainSkully | 3 comments »

Thanks in large part to WhatTheChuck, I’m giving serious thought to changing the design of the underbody of the table. With all due respect to Schroeder's table, which I prefer the looks of in many ways, I think the lack of a footrest underneath is a good thing, and the spindles underneath are magnificent, yet kind of a waste of time, energy, effort, and lumber as they’ll be hidden by chairs. I think the trestle-style design might be more pragmatic, and still embody the simplici...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #2: Template Adjustment

1834 days ago by CaptainSkully | 1 comment »

So, we decided that 72” was a bit overpowering. I yanked the pseudo-top out into the garage and cut a foot off, and then to preserve the Golden Ratio (we just watched a documentary about the Parthenon), cut the width down to 37”. This size is much better, and is more amenable to placing a Limbert Lamp Table or sideboard in the dining area. It seats six comfortably instead of eight, but we’d rather setup another table or TV trays instead of having a monolithic table 24/7. ...

Read this entry »


View CaptainSkully's profile

Limbert Lamp Table - Stickley #240 #1: Templates

1834 days ago by CaptainSkully | 2 comments »

So, between TreeFrogFurniture.BlogSpot.com and Robert Lang’s book “More Shop Drawings for Craftsman Furniture”, I decided that the corner of our dining room could stand an accent table. TreeFrog has built two different styles, so I “borrowed” the plans for the one I liked (he posted them online) and made my first template. I’m going to wait to make the interior template until I have the shell complete. The angles make things a bit messy. Like Tre...

Read this entry »


« prev 1 2 3 next »
22 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase