LumberJocks

Woodworking blog entries tagged with 'purpleheart'

  • Advertise with us
View degoose's profile

How to make a endgrain tumbling block butcher block board!

08-12-2009 12:13 PM by degoose | 50 comments »

Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...

Read this entry »


View Maveric777's profile

Uncharted Territory... My First Inlay & How I Did It

12-03-2010 03:47 PM by Maveric777 | 39 comments »

Well, I been hanging around here at Lumber Jocks for going on a year now. I have learned so much from so many, and can honestly say I owe a lot of what I know today to the sharing of knowledge here. So after attempting my latest “Exploration” into the wild world of woodworking I figured this would be a good a time as any for me to pass along a little blog on how I did my “Dreaded Inlays” ..... Long story short, I was hit up by a coworker asking me if I could build h...

Read this entry »


View degoose's profile

Chess board. #1: How to make a wavy chess board..

11-20-2009 12:20 PM by degoose | 29 comments »

This project is not technically finished so I will not post as a project..This part of the blog will deal with the cutting of arcs.I basically used one of the patron jigs I developed to cut the end curves for a Baguette Board…this pivots on the circle cutting jig. Cut two lengths of contrasting or complimentary timbers… I of course chose Purple Heart and Silver Ash…Silver Ash and Tasmanian Blackwood would have also been suitable… But if all you have is Walnut and Curl...

Read this entry »


View degoose's profile

Going wild at the chess board!!

04-26-2009 10:39 AM by degoose | 18 comments »

Welcome.Where do I start, at the beginning I suppose, I was born at an …..sorry not that far back!Ok let do this. [ I will be using imperial measurements throughout this blog..mainly ‘cause all wood working should be in imperial not metric! IMHO anyway] To start :Select the timber you will be making this here crazy board out of. For me this was Silver Ash and Tassie Blackwood as they contrast and compliment each other. I also decide to usesome purple heart as an accent. No...

Read this entry »


View jeepturner's profile

Double Step Cutting Board, errr Hot Pot Holder

12-16-2010 03:38 AM by jeepturner | 10 comments »

After looking at SPalm’s step cutting board blog, I figured that I would have to try my hand at making a double step board. I found some cherry, maple and purple heart from prior projects I followed the instructions to but the pieces: After glue up and cutting the two sections, I knew I wouldn’t have enough, so I set my sights a little lower.I had enough of the triangles to make a hexagon. I really need to rethink the clamping process before I start the next one, and al...

Read this entry »


View WoodJediNTraining's profile

Make a Folding Out Feed Table for your Table Saw

02-20-2013 05:22 PM by WoodJediNTraining | 16 comments »

This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...

Read this entry »


View degoose's profile

Starburst Patterns.... #1: My version... a Kaleidoscope

11-18-2009 08:03 AM by degoose | 22 comments »

David Mitchell aka Patron first showed us his amazing starburst table ...a few months ago. David sent me a design…a rather simplified version.. This was his gift to me on Fathers day..This is my version of that design… It has taken me a while to get around to it. David I hope you like it!..Here a some blanks cut to size.. First I milled the stock to 5/16 and 2 inches wide… cross cut to just over 3 inches.I used Purple heart and European Walnut.. any complimentary or contras...

Read this entry »


View degoose's profile

Spirals #6: We are not finished yet.

06-03-2009 02:23 AM by degoose | 18 comments »

Next step is to make the ends of the segments curved. Shell-like if you want.For that we need a new jig.. Yeah I know some of you haven’t finished the first one..!This is ultra simple.Firstly a fresh piece of ply .. 1/4 ” is fine.I inserted a bearing to make this more durable .. same same as last one.This was positioned 4.5 ” from the end[centred on the width] and an arc cut on the end via the circle cutting jig.. same same.Cut two fences same as the one of the first jig &#...

Read this entry »


View BritBoxmaker's profile

Black and White Dots inc. Basic Mitred Box

04-01-2010 07:39 PM by BritBoxmaker | 23 comments »

This is an earlier project of mine that also neatly shows one of the simpler box making techniques I use, that of the mitred box with drop-on lid. First we see the basic components: On the left are the four sides, each with a 3mm slot routed in near the bottom to hold the base. The base is bottom right and is two layers of 1.5mm birch aeroply. The top is the last piece, top right. This particular one is a three layer sandwich; 3mm design, 3mm ply and 3mm maple (this bottom 3mm will loc...

Read this entry »


View WoodJediNTraining's profile

Make a Cross Cut Sled For Your Tablesaw

04-26-2013 05:44 AM by WoodJediNTraining | 11 comments »

The one Project Video I get asked the most to make is how to build a crosscut sled for the Tablesaw. Well there are a lot of videos out there on making a Cross cut sled, so this is my take on it. I hope you can take something from this video and use it in your shop

Read this entry »


1 2 3 4 ... 19 next »
189 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase