LumberJocks

Woodworking blog entries tagged with 'project progress'

  • Advertise with us
View bandit571's profile

Stepback Cupboard in Pine #14: Bookcase started

03-15-2018 10:47 PM by bandit571 | 0 comments »

OK, Those two longer sides, needed a rebate added to them. Once I figured out which was the “inside” “top”, Back and bottom and have both match….Clamped one side into the vise on the bench.. Checked the Wards 78 to see how it was set up.. Might be about right? full length shaving. Got both rebates done.. This will “house” the plywood back panel… Time to lay out for a few sliding dovetails… Used a book to set the sp...

Read this entry »


View ElroyD's profile

Moravian Workbench Build #1: Getting Started

03-15-2018 05:06 PM by ElroyD | 4 comments »

A couple of years ago I started to get more into studying 18th and 19th century hand tool woodworking. At the time, I didn’t have a shop, and didn’t have anyplace to put one. During the summer I put cleaned out a section of our goat barn, put up a couple of sawhorses with a solid-core door on top to use as a workbench, and began to play. Then daughter #5 came along. Needless to say, babies take up a lot of time, so things were put on hold. Now that she’s a little mo...

Read this entry »


View Tomy Hovington's profile

Octave Mandolin #20: Custom Octave Mandolin

03-15-2018 03:10 AM by Tomy Hovington | 1 comment »

This project was commissioned and was quite the undertaking. My customer wanted a Octave Mandolin with a archtop and flat backboard. Since there was no blueprints to make such an instrument I had to do research, compile information and sketch my own drawing to even start the project. This build stretch over a year and a bit and was just completed.The wood used in this project is AAA quilted Maple back sides and neck, Engelmann AAA Spruce top, ebony fretboard, binding, and peghead veneer. Maho...

Read this entry »


View cowboyup3371's profile

Stand Up Jewelry Box #14: Legs and internal assembly

03-15-2018 03:03 AM by cowboyup3371 | 1 comment »

I need a bigger workbench after events of this week – one of the main carcass boards fell and broke while I was trying to size and fit the legs before assembly. I chose not to use clamps as I needed full access to the sides and wasn’t ready to assemble it as it was still too cold. However, I did not lose as much time as I feared and am now set to finish this project up by the middle of next week with delivery scheduled for the end of the month. I still need to make a door to hi...

Read this entry »


View bandit571's profile

Stepback Cupboard in Pine #13: Drawer installed, plugs and other adventures

03-13-2018 11:27 PM by bandit571 | 0 comments »

Got the clamps off the drawer….needed to clean up the dovetails a bit. One place I could not get to when all those clamps were in the way..was along the back edge of the drawer’s bottom. Large square to mark a line, roughly centered on the drawer’s back….added a few screws.. Should hold things in place. Drawer front had a huge knot in it… Drilled a hole for a bolt. Then laid out the same location at the other end of the drawer front, so these match...

Read this entry »


View Steve's profile

Shop Notes #12: Box Joints and Jewelry Cabinets

03-13-2018 04:08 PM by Steve | 0 comments »

I have a chance to exhibit at a local winery in about two weeks, so I put myself on a plan to get some jewelry cabinets finished in time for the event. These cabinets were based on plans for a hanging Shaker cabinet in Fine Woodworking a few years back. I’m on my fourth generation of design iteration. These are now taller than the original and have two doors instead of one. In this go around, I’ve changed from lap joints for the carcass to box joints, which should give a cleane...

Read this entry »


View CaptainKlutz's profile

Antique Tool Box #1: Is this a joiner's Tool Box?

03-13-2018 05:52 AM by CaptainKlutz | 12 comments »

#1 Dislike blogs. This is a documentary.This series of posts was created to document a recent estate find and hopefully gather some information from the antique tool collectors that troll LJ for entertainment. Did not want to pollute the HPOYD thread and potentially lose information. Back story: I have been working wood for 40 years as a hobby. As I become more senile and slow down from my impetuous youth, have learned I like the “FEEL” of working wood and started using hand...

Read this entry »


View BrockF's profile

Small Shop Adventures #13: Hand Planing Trim Boards.

03-13-2018 01:55 AM by BrockF | 1 comment »

For the ceiling trim in my parents place I am going with 1×4 boards with a 1/2 inch square strip along the upper edge, all painted white. I am using poplar because it paints great and is such a pleasure to work with. One of the challenges I face is that the ceilings have a few spots where they are not exactly flat, either because of time or because of muddling, paint, repairs or both. This would be essentially invisible except when you try to put a trim board up. I can’t do...

Read this entry »


View bandit571's profile

Stepback Cupboard in Pine #12: Build-a-drawer, 101

03-11-2018 08:41 PM by bandit571 | 1 comment »

two days to build one drawer? I am getting slow in my old age… Anyway, this may be a bit long, better get settled in…. Cut this to size..goal being to build a drawer around it. Had a couple “left-overs” for the sides, they needed to match in width and length…Length was at the bandsaw, later the mitre box. width was the easy part. Then “shot” the end grain straight..Set the sides aside for a bit. Corner joints will be through dovetails&...

Read this entry »


View bandit571's profile

Stepback Cupboard in Pine #11: Top is done, case assembled

03-10-2018 03:07 PM by bandit571 | 0 comments »

Worked in two separate sessions yesterday….had a morning “shift”, a trip to get a CT Scan on the head, then when we got back home, an evening shift….Morning stuff:Top was removed from the clamps, set aside for a while. Ripped a few 1×1s from the leftovers…needed to build out the drawer runners, for the drawer to slide on….also needed guides to keep the drawer centered in the opening… A bead of glue and a screw. Both are attached to the webf...

Read this entry »


« prev 1 ... 5 6 7 8 9 10 11 ... 930 next »
9292 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com