LumberJocks

Woodworking blog entries tagged with 'planer'

  • Advertise with us
View therookie's profile

My First Real Attempt at a project. A shaker end Table #1: Kind of Commission #1

12-05-2010 03:07 AM by therookie | 1 comment »

Well in all reality me building my new workbench is going to have to wait. The reason that I am saying this is just because of the cost and I could possibley have my very first commission. When I say this I am talking about my local furniture shop is going to put a table that I am planning on making in their shop on consignment for me and help me get my name out there. When I talked to the owner of the shop, he said that if this peice looks really good to him and he can sell it and still make...

Read this entry »


View ttocsmi's profile

Double Single Bed #2: Big Pieces Into Small Pieces

12-16-2015 04:01 PM by ttocsmi | 0 comments »

Well, the SE Michigan weather continues to be more balmy than frozen, so work on the bed frames continues. I’m out of propane now, too. This week I received the bed bolts from Horton Brass ($4.50 each) & placed an order for the box spring fasteners / bed irons ($2.25) and bed bolt covers ($1.85) from Baltimore Hardware. I rough cut, jointed, & thickness planed the pieces for the posts, 2 x long and 2 x short for each bed, from 8/4 red oak. For the first 12 inches, rippin...

Read this entry »


View yellowtruck75's profile

Milling black walnut

08-03-2015 02:11 AM by yellowtruck75 | 0 comments »

Using my 16” American jointer and 718 Wood Master planer to mill some 8/4 black walnut. https://youtu.be/1UgNZIwNiwI

Read this entry »


View bandit571's profile (online now)

Simple box to hold candy #1: Joinery

07-15-2017 11:05 PM by bandit571 | 1 comment »

Had a request to build a little box to hold/hide candy in….I had a plank planed down to about 7/16” thick..or so. 6” wide. Has a bit of figure to it.. Needed to get five parts out of it..Mitre saw to cut them out.. You were expecting a motor? Ok, the 5 parts needed.. A panel for the lid, an end a front and back and another end. Got out the usual suspects.. I use one combo square to set depths, another to do a knife line across. The mortise chisel is to ...

Read this entry »


View Matt's profile

New Stuff!!! #2: Dewalt Planer!!

10-26-2016 07:03 PM by Matt | 4 comments »

Hey everyone, It’s been a long time since I posted, but I just wanted to say that I finally got a Planer. It’s a Dewalt, and it’s about 10 years old, but it was free and almost unused. It was my uncles, and he gave it to me indefinitely. If he needs it, he will obviously be able to borrow it, but otherwise it’s mine I guess. I wanted to get a planer that could use helical heads and I don’t think that this model will do that, but alas. I ran a board through ...

Read this entry »


View mchapman87's profile

Honey locust bench. #1: The start of my outdoor bench.

02-08-2017 04:51 PM by mchapman87 | 1 comment »

So I am finally getting started on making a few new pieces out of my small garage woodshop. Money has been tight and I haven’t been able to get the wood I need to fiddle around with. I was given a load of rough milled lumber from a friend who is just learning how to use his mill. Most of the pieces are not flat, pretty wavy but are fairly thick. This helps because I can take off some material flattening the pieces, making them useable boards. He didn’t charge me an...

Read this entry »


View Tony19's profile

End Table #7: Top, chore

06-02-2016 02:37 PM by Tony19 | 0 comments »

Today I made my top by glueing 3 pieces of oak together and sanding it. I did have some tribe making this because it would not fit in the planer so I had to use the handsander to sand it which took much longer. I also made my chore, and to do it, I used the dove cutter and glued the pieces together. I fitted the bottom in and put the false chore front on it and put the handle in. I sanded it and now it looks great in my end table.

Read this entry »


View johnstoneb's profile

Musical Instruments #2: Starting the Marimba

11-20-2016 03:36 PM by johnstoneb | 6 comments »

I have finally started on the marimba. I am following the plans I got from makeamarimba.com. They are a good plans although some times you have to translate from oz to usa english. I did a lot of searching on line on commercial marimbas and settled on padauk for the keyboard and cherry for the frame. The preferred wood for concert keyboards is rosewood. I called my hardwood supplier to get a price on rosewood when I was able to breath again I decided padauk was a good keyboard wood (most...

Read this entry »


View Josh Hall's profile

Opus Magnum Dining Chair Project Is Finished

06-15-2013 10:23 PM by Josh Hall | 0 comments »

i have a new blog post about my dining chair project, check it out on my website. http://joshhallfurniture.weebly.com/1/post/2013/06/opus-magnum-dining-chair-project-is-finished.html

Read this entry »


View mchapman87's profile

Honey locust bench. #2: Slow progress is still progress nonetheless.

03-15-2017 07:52 PM by mchapman87 | 3 comments »

Quick update from my honey locust bench build. I have been trying to juggle this in with a myriad of other projects that seem to pop up daily. My daughters birthday is tomorrow and I had the pleasure ( heavy sarcasm) of putting together this monstrosity of a swing set. I pray that one day my daughter will have kids and have to suffer the same fate as I haha. Two whole weekends of battling this behemoth and it’s finally complete. Now I can focus on some of my stuff, hopefully. I ...

Read this entry »


« prev 1 ... 81 82 83 84 85 86 87 next »
868 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com