Cap iron or chip breaker, blade or iron – Some folks write treatises about which term is “correct”. I use the one that comes to mind, they mean the same thing. Chip Breaker Function The chip breaker adds mass to the blade and adds stiffness to the blade, and with the lever cap pushing down, seats breaker & blade flat on the frog, creating more blade stiffness (cap iron). A very important, but lesser known, function of the chip breaker is to create a force down the chip fibers as the...
Ever since I saw Mafe's router plane I’ve had the desire to make one. As I do most often I look here on LJs for inspiration. Well, I found it. As I searched I came across this gem of a router plane made by Tinnocker. Tinnocker got his inspiration from Mafe’s design as well. I used a picture of Tinnockers design to come up with my version of a router plane. The body of the plane is hard maple. The handles are from some old chair spindles I had laying around, The plane iron is a ...
There’s a new Little Good Pieces blog post: Review – Hock Plane Irons. My first Hock plane irons for my block plane and a Krenov smoother. Check it out! http://littlegoodpieces.wordpress.com/2011/05/31/review-hock-plane-irons/
Body done, wedge done, plane iron done. If you are anything like me, eagerness to see some shavings has replaced all other desires at this stage! With a bit of luck, paper thin shavings will be curling out of the mouth. Isn’t it great! If not, don’t despair…. LET’S FINE TUNE: 1. True the plane sole. This is done with the blade in place but well away from the mouth and the wedge set up tightly as it would be in use. Why? With the wedge set, our plane is in “tension”. The wood actuall...
If this is happening a little too slow for your liking, it is because I have to make sawdust all day long to keep the wolf from the door. That is 10 hours gone. Making these little planes and blogging about it is mostly a night time affair, after taking care of normal daily chores and duties! We have made a plane body and it is looking pretty good! Time to do some metalwork.This is what we want to achieve: At the top is the finished plane iron, below is the material I made it from; ...
Low angel shoulder planeMaking a blade from another plane iron. This is the second part of the blog, in last part the plane body was made. This is where we will end, Div’s shoulder plane on top, then mine and finally what this part is about; the plane iron. Since I have a handful of block plane irons I got for next to nothing, I will ‘kill’ one of these.Measure the width of your shoulder plane and add a little for later tuning (I added 1mm).Draw this on your plane ...
- My Journey As A Scroll Saw Pattern Designer - 1560 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1585 entries
- frank - 417 entries
- degoose - 395 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 276 entries
- William - 258 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 188 entries
- Rustic - 188 entries
- Chris Davis - 183 entries
- BritBoxmaker - 181 entries
- Smitty_Cabinetshop - 175 entries