Hey everybody, after a few personal messages here is my version of a how to on a Drunken Checker Board. I of coarse bow to the Chairman of the Board and pay tribute with beer. This is a Off-Checker pattern I call “Drunken Alice in Wonderland” The “serendipitous” nature of this piece is appealing in a far out sort of way. Here Goes… So first I prepare the Material. I am using Hard Maple and Walnut both are surfaced flat and cut 1” x 9” x 14&...
Hi guys ,, I had a request to make a tutorial with regards the endgrain Tumbling Block Design.First off,.., You need to decide the size of the blocks…. for this example I used 1” stock… Or something similar.. actually just over .. once dressed. Set the blade of the table saw to 60 degrees.. a bevel box makes this simpleI use the INCRA fence system so it is easy to rip bevels off side of the blade.Once the bevels are ripped measure the length of the bevel and move the f...
Updated 1/15/12 How to make an Art Box by Andy Campbell Safety Be safe! Guards, etc…may not be visible in the pictures. This is written for woodworkers of all skill levels.But, please keep in mind that this is not woodworking #101. I am writing this in a step by step manner that should be easy for a beginner to follow, but some basic understanding of tools and terminology is required.I ask that the more advanced woodworkers be patient and not be offended. I don’t wish to test your...
For those of you who asked me for a tutorial on how to make the zig zag legless vegetable death table (cutting board), here is my best shot. I am far too impatient to take photos when I work, so I decided to illustrate the process using some good old Adobe PhotoShop. I hope you find this useful and informative. I will outline the process in 10 steps below. I have assumed that when viewing these steps that basic woodworking skills are familiar to you. If you have questions, or run into snag...
I started this project after building an assembly table from an issue of Wood Magazine (March 2010). The table was a lot of work (the torsion box top) but the main unit holding the table up was an easy build. That’s when I hit upon the idea of using the same design for a group of extra tables for other uses. I’ve built a number of these already, and am using one as a router table, a miter saw station, and a sharpening station. It is built using standard re-dimensioned co...
I am working on both tutorials for a couple of reasons, to correct many areas that were unclear and to add in all the fixes I made in the comments sections. Some of the pictures I used were no longer showing up due to a glitch on the website I had them stored at and the tutorial made little sense without them. So I decided the text needed redoing also. I am very busy right now, but hope to get around to it soon.Stay tuned.Andy
The quick and dirty instructions on how to make a zig-zag pattern cutting board. Click on the pictures to see a full size image. Choose a couple different types of hardwood. The more colors the better. Below is cherry, maple and walnut. Rip strips of wood any width so the total with is about 12”. This is the width that will fit through my planer. The beauty of this is that none of the widths have to be the same. The board shown below is made of scrape wood. If you only have shor...
Well, I was asked to put together a blog on how I made my segmentd ring. Since I had to make a new one for myself, (first one too small) I thought I would go ahead and do a step by step picture tutorial. My first time ever doing something like this , so hope it comes out OK. Here goes; Wood Selection The first step in making the ring is deciding what woods to use. As we all know, the selection is quite large. One of the most important things is color, but the most important is hardne...
I was absolutely overwhelmed by the positive response to my Zig Zag How To blog post yesterday, that I decided to brainstorm some possible combinations (on my lunch break) using the basic steps I outlined yesterday. All of the same techniques and steps apply, and really the only difference is the woods and measurements that make up the original “sticks.” Same rules apply to width = height. Length is up to you. Please experiment with whatever measurements and combinations strike...
Awhile back Wood Magazine had an article on building a mobile outfeed table that would fit over your table saw. Since I need all the space in my garage I can get, I went ahead and built one that would fit over my table saw to give me some much needed work space and a handy outfeed table. I thought this was pretty spiffy and a great use of space. As I always do I look at the latest project posts on Lumberjocks looking for inspiration for my next project. Whilst browsing I came ac...
- My Journey As A Scroll Saw Pattern Designer - 1266 parts
- Extremely Average - 324 parts
- Workshop Development - 95 parts
- A journey into the workshop. - 88 parts
- Daily Update - 87 parts
- Just for Fun... - 82 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 75 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1288 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 370 entries
- Ecocandle - 325 entries
- MsDebbieP - 311 entries
- Karson - 301 entries
- Martin Sojka - 297 entries
- William - 257 entries
- Betsy - 221 entries
- mafe - 216 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Rustic - 184 entries
- Chris Davis - 183 entries
- shipwright - 168 entries
- PurpLev - 163 entries
- BritBoxmaker - 161 entries
- stefang - 148 entries