This project is really finishing nicely. I just need to mill out boards for the benches, and add some center supports to flatten out the top a little better. Very happy with it so far. I started finishing it with Teak oil, but I don’t like the yellowing affect it has on the juniper….any suggestions on what would be a good outdoor finish?
My mom bought a simple 2×4 picnic table a few years ago and the top has not held up well. The boards are twisted and warped, and I thought it would be a good “test” subject for a new top using an idea that I have had for a while. Juniper grows with a very rapid taper, and finding trees big enough to make wide straight edge boards out of are few and far between. So I had the idea of alternating wide/skinny ends of the boards and leaving the live edge intact to give me the wide...
One of mine and my wife’s most favorite places on earth is Knoebels Grove Amusement park, located near Elysburg, Pa. The park was started back in 1955 as a “hang-out” for local loggers in the area and grew from there. It now houses some of the best wooden roller coasters in the world and is a free-entry, family friendly park with great rides, unbelievable food and some of the best campgrounds in the region. You can even walk around the park with your dog (on a leash, or ...
As I was working on the sculpted top, I found a bullet that I somehow milled in half with my chainsaw. I’m sure that was pretty hard on my chain at the time as the jacket of the bullet is still intact!! Busy week so I didn’t get as much done on this project as I would have liked, but it is coming along nice. All 4 boards for the top are almost done shaping, and all the material for the frames has been rough cut to size. I spent an evening building 8) 4’...
Well, all the great compliments from the replacement top (http://lumberjocks.com/projects/68932) have helped inspire me to keep my motivation up to build a full custom table. So I intend to keep in progress pics through the entire build of this table. I hope you enjoy following along! Step 1: Mill out the boards from these ugly logs. Step 2: Lay out the boards how I want them to fit together, and then cut to length. I went with 7’-1” on this project as it worked well...
Well, its all together and ALMOST finished…..I ran out of teak oil before I could step back and say “DONE”, and all the stores were closed by this time. I’ll have to finish it up tonight. This will be the final blog before I post this as a project. Overall, I’m very happy with it, and have gotten very positive comments on the design. I rushed the final assembly more than my usual critical eye would allow, (which means I cut corners on finish sanding ALL surfaces...
I was struggling with how I wanted to build the frame for this table when it occurred to me that I had a whole pile of cut offs that are left over from the outside of the logs after milling out boards. Perfect!! I have a flat side to work with for joining the frame together which simplifies trying to scribe logs together, and it cut the work of harvesting more logs or cutting more boards. Always nice when you can find a use for scraps!!
In Part 2 I continue with the Octagon Picnic Table Build. I will start off by creating the Seat Base Assembly Parts cutting them to size and bringing together the assembly. Plans for this project will be available for download shortly. A link to the plans will be added to this description once complete. Support Our SponsorsClear View Cyclones – http://www.clearvuecyclones.comIf you are interested in purchasing from Clear Vue be sure to use the coupon code LANEY for 5% off yo...
This is Part 1 of a new build. How to build an Octagon Picnic Table. For as long as I can remember I wanted to build an Octagon Picnic Table and I looked everywhere for a good design and plan. Well I finally found one that was perfect for my patio. I got this design from Woodcraft Magazines April May issue Volume 10. It was a design and article by Bill Sands. Bill did a great job with this article and made it very easy to follow along. He built his table out of cedar and wow did it look grea...
- My Journey As A Scroll Saw Pattern Designer - 1598 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1623 entries
- frank - 417 entries
- degoose - 397 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 279 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 218 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 187 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries