LumberJocks

Woodworking blog entries tagged with 'particle board'

  • Advertise with us
View christenite's profile

Work Station #1: Part 1

207 days ago by christenite | 3 comments »

I recently inherited my grandpa’s vintage 10” craftsman table saw. It had a broken fence and was on a wobbly metal cart that had been pieced together. I have no idea honestly if he ever ripped anything more than 3-4” on it because of the fence. Anyways, the saw runs great and I want to put it to good use. Some of the problems presenting me were: 1) Saw will be in a garage shared with other stuff2) The stand and fence needed to be replaced3) My young kids play in the garag...

Read this entry »


View StumpyNubs's profile

The Stumpy Nubs Workshop #27: The world's greatest pin jig! & Who says particle board is useless?

656 days ago by StumpyNubs | 19 comments »

The Bunyan brothers challenge me to a particle board contest and that can only mean one thing… A NEW JIG! You’ve never seen a shelf pin jig like this! And I gives my hard learned, top five tips for ending your hand plane frustrations. Plus a bunch of other stuff, so… enjoy! (Hint: Here’s the new jig…) After you watch this one, visit Stumpynubs.com for more woodworking goodness! (Friend us on facebook, follow us on Twitter, and visit the Stumpy Store ...

Read this entry »


View Metrotek's profile

CLAMP FOR MY BIESMEYER FENCE UNDER CONSTRUCTION

838 days ago by Metrotek | 1 comment »

Greetings to all once again; I am attaching photos of the clamp for my new Biesmeyer style fence that is under construction. It came out fairly well.The circular pads are adjustable by carriage bolts threaded in to t-nuts to correct any undesired angularity. The ¾” dowel is a plunger that the cam pushes to lock the fence in place. The two piece pad that the dowel pushes will have an elastomer sandwiched between the pieces to provide a spring action so the cam can over clamp it...

Read this entry »


View Metrotek's profile

SAW CABINET #1: BUILDING MY TOY SAW A CABINET, OUTFEED TABLE, AND MORE

862 days ago by Metrotek | 3 comments »

Here are some more photos showing the progress of my saws cabinet. It fits perfectly where it’s supposed to then when I connect the outfeed table and Biesmeyer style fence to it there should be no problem with maintaining alignment.I think I’ll put about two feet out the back for the outfeed table not including the mounting/hinge area. I’m going to make my own hinges instead of purchasing them; just brackets with dowels for the pins. Then, probably 8...

Read this entry »


View nobuckle's profile

Learning the hard way!

1346 days ago by nobuckle | 10 comments »

Today I started working on a router table idea that I came up with. I currently have a router table (more like a cabinet really) but it takes up to much room in my shop. If you’ve read my profile you know that I only have 99 sq. ft. of main shop space, so maximizing space is a constant challenge. I’ve decided to move the left-hand table saw extension of my table saw to the right side and replace it with some material that could be used for a router table. The material I select...

Read this entry »


View Bob Simmons's profile

Let's Build a Drill Press Table

1441 days ago by Bob Simmons | 14 comments »

The drill press is a terrific tool in the woodworking shop especially when it has a drill press table that conveniently clamps the work, provides a fence for repeatable and accurate cuts, and also offers a safer working environment. The drill press was originally set up for metal working and most tables that come with the drill press are small metal tables. As a result, the metal tables can be rather awkward for use in the woodworking shop. A better solution for the woodworker is to buy...

Read this entry »


View Brian Havens's profile

The Straightedge (video) #1: Working with Melamine

1677 days ago by Brian Havens | 15 comments »

This is a re-edit of the video that got me started doing videos. Unfortunately I knew very little about shooting and editing video at the time. In fact, I shot the video with a web cam, so the video quality is poor in parts. The re-edit gives it a nice face lift, but perhaps in the future, when I run low on topics, I can re-shoot the video. (Full steam ahead on Router Inlay!) Here is the link: Working with Melamine

Read this entry »


View John Gray's profile

Edge Banding Particle Board with Solid Hardwood

1837 days ago by John Gray | 9 comments »

I’m building an 18” V-Drum Sander from http://www.stockroomsupply.com/V_Drum_Sander.php Stockroom Supply. I was given a Particle Board piece to use as a top it’s laminated with a thin slick veneer top and bottom. I’d like to band the edges with Oak that I already cut and mitered. The question is how to attach the Oak to the Particle Board edges? I’m read plenty of horror stories about splitting the Particle Board when using screws and/or nails to attach it. ...

Read this entry »


View roundabout22's profile

What the wife wants I guess she gets #2: Entertainment Center #2

1933 days ago by roundabout22 | 0 comments »

Once I had the cabinet home I (she) had to decide how she wanted to set up all the electronics. We (she) decided it would be better if both the top and bottom sections had doors on them, and we needed to put a couple shelves in to hold the dvd player, vcr, etc… Space in the upper opening is a little tight so there will be just enough room for a shelf, and by taking out one of the drawers we can put another shelf in the lower cabinet. This is what I got accomplished shortly after ...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase