Woodworking blog entries tagged with 'outfeed'

  • Advertise with us
View uMinded's profile

Ridgid R4512 Table Saw #1: My R4512 Setup

01-28-2015 12:33 PM by uMinded | 10 comments »

Totally set up R4512 cast iron table saw. Lee valley brand router table insert 05J25.01 router is a BOSCH 1619 EVS which is a beast. Outfeed table out of three door hinges and a piece of planed to thickness 2×4 and 5/8 birch MDF. Recycled front fence from old crosscut sled. Maple with a T-slot extrusion. NOTES:1) If you tighten the blade lift handle with the center nob the blade misalignment goes away! I figured mine was good as I ALWAYS tighten mine (Prevent lifting with a ...

Read this entry »

View PJ72's profile

Season of shop upgrades #2: Table Saw Outfeed

02-16-2014 10:34 AM by PJ72 | 3 comments »

A need for out-feedI have tried using out feed rollers and various stands for some time and have never been satisfied with the results, especially when cutting large sheet goods on the table saw. For reasons including safety and quality of cut, I decided that I needed an out feed table system. Primary ConcernFor my garage workshop I needed a solution that was easily stored out of the way quickly with minimal storage space. I patterned the out-feed table on a design by Dwayne Intveld in t...

Read this entry »

View Garry's profile

Ultimate Mobile Woodworking Bench (UMWB) #9: Overall impressions of my Ultimate Mobile Woodworking Bench

01-05-2014 09:52 PM by Garry | 3 comments »

I have to say I’m very pleased with the UHWB. I started work on it a few months ago and it’s been usable for the last month and a half. These last two weeks on Christmas vacation gave me time to really focus and get it finished. After way too many years of makeshift garage workshops in rented houses, it feels great to have an organized workspace that I know I can take with me almost anywhere. I built a small bookcase for my wife’s craft room and it went very smoothly. Her...

Read this entry »

View Mainiac Matt 's profile

TS outfeed table with downdraft #1: The Nutty Professor is at it again

05-21-2013 01:24 AM by Mainiac Matt | 3 comments »

This view shows the back side of my recently refurbished TS. There are ~46” between the saw and my primary work bench. I lowered the bench to match the height of the TS @ 32-7/8” and planned to bridge the two with an outfeed table…. but I wanted to do something different with it. Since I have two 4” DC lines running back there, I figured this would be a great place for a down draft table. Here’s the preliminary design… To maximize air flo...

Read this entry »

View RaggedKerf's profile

Miter saw station/router table...on wheels!

11-28-2012 11:56 PM by RaggedKerf | 3 comments »

For a while now (since June when my wife and I ripped out the powder bath vanity and put in the garage) I’ve been kicking around the idea of making a miter saw station. I had planned to put it on wheels to allow me to move it around the garage and out of the way when not in use. Then my father-in-law gave me his router table….and the idea got a little more complicated and took a nagging position at the back of my mind for months. I kept coming back to it and kept coming up em...

Read this entry »

View curliejones's profile

Opinions please #1: Solid core door topping the bench

10-05-2012 11:46 AM by curliejones | 7 comments »

Greetings, fellow LJs. I have a puzzle that needs a solution. I built a workbench that I particularly want to roll into place for TS outfeed. I hope to soon delineate the steps taken and justify decisions to help the next guy not do so much planning. The “opportunity” before me goes like this: I have a very nice solid core door for the workbench top and a piece of hardboard for the sacrificial top. After reading the “two-sided tape” tip several times, I bought a roll. ...

Read this entry »

View Robsshop's profile

Table Saw Adjustable Extension support Details

03-01-2011 07:36 AM by Robsshop | 14 comments »

I have had some interest from a few L J’s on a TS feature built into My saw’s fence extension rail. One Member suggested that I put together some details and pics and enter it as a Blog, so here it is. This is My first Blog, so I hope I can make sense of this simple but useful TS fixture. It consists of a few easily fabricated pieces that can be be put together with very little difficulty and can be adapted to most TS’s with hollow extension fence rails ! The main beam th...

Read this entry »

View Hopdevil's profile

The suspended outfeed table

02-19-2011 06:59 AM by Hopdevil | 10 comments »

There are some fabulous examples of outfeed tables on this site and others. Most of them rely on legs or wheels for support. My problem is that my garage floor is VERY uneven. Since I move my saw around a lot, I would have to spend a lot of time leveling it to compensate. I wanted to come up with something that I wouldn’t have to keep adjusting. I decided to create one that is suspended from the rail of the fence support. Here is the saw before starting. I created some supports from 2 ...

Read this entry »

View Rob Vicelli's profile

My experience with a new Sawstop, board buddies and Digital fence.

02-07-2011 10:51 PM by Rob Vicelli | 5 comments »

After being on order for 3 weeks I finally received my PCS 1.75 SawStop with 52” Rails (Gloat) last week. I guess the wait was not that bead because I was able to research, plan and purchase the accessories I wanted to use. As stated by others the package was excellent. I did have some trouble installing the front fence tube but a quick call to SS (In which they answered the phone with a real person) resolved the issue. A change in the way you square it and tighten it to the rail was all that...

Read this entry »

View sub3wood's profile

Table Saw Outfeed Craftsman 21828 #1: Craftsman 21828 Outfeed Table

02-06-2011 09:42 PM by sub3wood | 2 comments »

Hello All, This is my first post asking for help. I have been looking at the site since November and was finally able to join the site. I am very impressed with all the information that you have on here and look forward to learning and sharing. I am trying to build an outfeed table for my Craftsman table saw (21828). It is nice having a new saw but like my old table top saw the need for the outfeed is huge. I have started by cutting a 4’X4’ table out of Melamine and 3/4&#...

Read this entry »

1 2 next »
18 entries

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

Latest Projects | Latest Blog Entries | Latest Forum Topics :: gardening showcase