LumberJocks

Woodworking blog entries tagged with 'miter saw'

  • Advertise with us
View Dennis Fletcher's profile

The making of a Telescope Eyepiece box #1: Telescope Eyepiece box

01-15-2010 05:06 PM by Dennis Fletcher | 1 comment »

I have been commisioned by a young man who is an ameture astronomer to build for him an eyepiece box. That is, a box that will hold all of his eyepieces, his filters and his maps without any damage to the pieces. He travels with his telescopes every year to SC, I believe, so it needs to be secure enough to not open up on him and to withstand an accidental tumble or two. I have had to learn how to use a dovetail jig and have done pretty well with it. However, due to my lack of proper pla...

Read this entry »


View BlankMan's profile

Chop Saw Dust Hood #7: Video Of It Suckin' Up da Dust

12-30-2009 07:01 AM by BlankMan | 21 comments »

I shot a video of it in operation in High Definition Video and Stereo (really!) the link is below. I thought I’d show two last pictures of it as installed. The first showing the clearance cutout in the top allowing the saw to swivel (the clearance looks larger then it is due to the angle the shot was taken at, it’s just over a 1/4 inch), and by request a picture showing the connection to the cyclone duct. The swivel clearance. Its connection. Last but not least… ...

Read this entry »


View rweitz's profile

Workshop #2: So you want pictures....

12-29-2009 10:07 AM by rweitz | 5 comments »

Several of you requested pics so here they be! As you can see lots of “non-essential” stuff in here. Front of the workshop area Back Wall of the workshop area Mark 1 drill press Craftsman Tablesaw – 113.298.341 Delta chop saw and Ridgid folding miter saw stand – love this product.

Read this entry »


View sras's profile

Out of the scrap pile and into a gift #5: Arched Candle Holder - On to New Heights

12-21-2009 10:45 PM by sras | 3 comments »

It seems like the arched form needs to be lifted off the table by some amount. I’m not sure by how much. My technique in situations like this is choose from a range. Start with too little and keep adding until it seems like too much. Somehwere in between “too little” and “too much” there should be a “just right” or at least a “close enough”!In this case I start adding spacers underneath each end. Here is the range of heights. The wi...

Read this entry »


View BlankMan's profile

Chop Saw Dust Hood #5: Well It's In The Home Stretch

12-19-2009 10:52 PM by BlankMan | 5 comments »

Three coats of poly on the areas that could be accessed in this position, flip it over and three on the areas remaining and the next blog entry should be of it in place, connected, and ready to go.

Read this entry »


View BlankMan's profile

Chop Saw Dust Hood #4: Plumbing To Connect The Chop Saw's Dust Port

12-16-2009 06:52 AM by BlankMan | 4 comments »

Well I got sidetracked restoring the Jet sander but did spend time on this while working on that in between waiting for parts. I cut out the circle for the saw swivel clearance like six times. There was really no good way to measure it and get it right the first time because like I said with the blade guard, handle, and motor, the cutout is closer to half a teardrop then a circle. So I’d put the hood in place, put the saw in place, and see where it bound or was too close and cut it bigg...

Read this entry »


View kosta's profile

Episode 48 Napkin Holders

12-16-2009 01:07 AM by kosta | 1 comment »

In this video I go over some of the napkin holders that I have built.www.kostasworkshop.blogspot.com

Read this entry »


View Dusty56's profile

Cutting boards in progress #1: Cutting boards in progress

12-14-2009 04:14 AM by Dusty56 | 4 comments »

Using up some scraps here…..just made the basic boards today. Tomorrow I hope to work on the corners and edge treatments and juice grooves and then get them soaked with Mineral Oil : ) Thanks for looking ! Ooops ,sorry …... Where to add photos here ?

Read this entry »


View Seth's profile

Key Holder: Closer

12-01-2009 08:21 AM by Seth | 7 comments »

After Thanksgivings #s two and three, after two days of painting our bedroom and cleaning up the mess that created, it was finally time to turn my attention to the keyholder. My dad was nice enough to give me his inherited router, which was the piece of equipment that lit a fire under my hobby-searching self. For some reason, the idea of rounding edges or being able to cut canals out of wood made the whole thing a lot more appealing. Here’s my makeshift workshop: That’...

Read this entry »


View BlankMan's profile

Chop Saw Dust Hood #3: Outlet & Saw Swivel Clearance

11-30-2009 06:30 PM by BlankMan | 2 comments »

Well, I didn’t get to spend as much time over the 4 day Thanksgiving Holiday weekend as I wanted to working on this but I made some progress. I was actually hoping to have it done but not having the time and having to determine and make the template to do the cutout for the saw swivel clearance took a while. The cutout is not a continuous arc of the same radius because you need clearance for the guard here, the handle there and then the motor. And determining where to put the outlet was...

Read this entry »


« prev 1 ... 34 35 36 37 38 39 40 ... 48 next »
480 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase