This is a router table I’m working on for my shop. I was able to incorporate most the features I needed and plan to use it often. It isn’t finished but most the major parts are in place. I purchased the Incra twin linear, router table top, woodpeckers router lift and the porter cable 7518 motor from Woodpeckers Inc back in 2002 or 2003. Finally, she’s in working order. Since the last post I was able to complete the rear ...
Hello everyone, a few people have asked me for plans on how to build the folded slotted chair I made so I decided to give it my best shot to measure the pieces and give a description on how it was done, so here we go. Wood Used: Ash Parts List:1 1/2” x 3/4” x 48”: 21 1/2” x 3/4” x 38”: 21 1/2” x 3/4” x 36”: 71 1/2” x 3/4” x 34”: 21 1/2” x 3/4” x 15 3/4”: 91 1/2” x 3/4” x 6”: 12 ...
Resawing lumber bandsaw JIG – HOW TO MAKEOr your own little mill, if you find a nice peace of wood in the forest! I visited a friend the other day, and in his firewood pile I found these nice pieces of wood, and could see a little box, a new handle for some chisels, a mallet and God knows…So yes a new jig was needed… Or perhaps wanted – and since I love making them, here we go: First a plywood sled that fits your bandsaw size.Route some T-tracks (or buy s...
How do you install a grid work inside a tea box so it looks like this? Here is what the lift-out grill work looks like inside the tea box. This is what the lift-out grill work looks like outside of the box. The small compartment to the left makes a chain pocket so the stop chain doesn’t get tangled with the teabags... Why use Venetian blinds for lift-out dividers? By the time you plane, sand, and finish slats to make dividers inside boxes you have a lot of time and ...
Hello all,I have been asked to give a class on making a wood bracelet similar to this one. http://lumberjocks.com/projects/18322 I want to point out that we will NOT be using the special jig I made. I have a different way to get the same results which does not require each of you making a jig. Part #1Getting started and choosing wood. Step #2Preparation off wood and cutting notches. Step #3Drilling holes and shaping. Step #4Finishing and final assembly We will begin be goin...
The following is an addition to The Apprentice and The Journeyman woodworking video series, Let’s Build. The dedicated dado sled for the table saw is a highly versatile woodworking shop fixture that can expand the woodworking approaches used by many woodworkers. Dado blades are used on the table saw instead of a typical saw blade and the dado blades are often said to be “stacked.” This term implies that the dado blades, chippers, and shims are combined to create a cert...
I wanted to try my hand at making hand planes, the shop needs several. Struggling with the design concept, I bought a book “Making Traditional Wooden Planes” by John M. Whelan, it was no novel but a good source of wood plane design info. It’s worth reading if you’re researching wooden hand planes. Trying to keep the first plane simple I decided on making a small shoulder plane in the Krenov style. Looking around my shop I found an old 1” chisel. It is harder than heck, so I took it a...
Intro- I’ve been using a lot of wooden planes recently and have really come to enjoy their lightness and the feel of wood sliding on wood. Obviously there are a ton of vintage woodies out there; however, I quite enjoy making my own versions of them. They are a lot cheaper (if you have some time on your hands) and you don’t have to deal with old warped wood and a host of other problems you may encounter. I can’t say I am an expert by any means, I’m simply sharing my...
This board is not part of the 150.. I showed one of the 150 to a friend and she wanted one but a little larger,This is the way it was made.Cut some bits of board. NGR SA TBDress all sides.This is to see the way it will look with the stripe. Cut all pieces to 250 mm.Join the NGR and edge with TB on one and SA for the other.Glue a sacrificial board to the SA prior to cutting the arcs.This is the arc cutting jig.. a slight variation on the patron jigSet the stop with a nail… high tech I kn...
I have been thinking of building a small band sawmill for about a year or more and finally decided to make one. I built a bandsaw from Mathias at woodgears and love it. So I decided to use the same design but modify it to cut horizontally. It will only be used for small logs 6 feet long and no bigger than 28 inches in diameter.It needs to break down easily for transport to my dads and back. I like the lumber smith saw so I think I will make it similar. http://www.lumbersmith.com/ The frame...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 106 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 419 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries