LumberJocks

Woodworking blog entries tagged with 'medallion'

  • Advertise with us
View summerfi's profile

Saw Medallion Reference Guide

02-13-2014 01:52 AM by summerfi | 52 comments »

SAW MEDALLION REFERENCE GUIDE Saw medallions, or label screws as they were originally called, are invaluable for identifying old saws. Additionally, many of them are small works of art in themselves. I don’t know of a comprehensive reference source for saw medallions that covers all makers, so I decided to start one here. My intent is to add to this list over time to make it as complete as possible. If you run across a medallion that is not listed here, post a picture of it in the comments...

Read this entry »


View Brit's profile

Saw Talk #30: Warranted Superior Medallions

11-24-2013 11:14 AM by Brit | 24 comments »

Over on the Saws, using collecting, restoring buying forum, summerfi (Bob) asked the following question with the accompanying collage of warranted superior medallions: “I have a question about Warranted Superior medallions. I’m most familiar with the eagle medallion, which came in several versions. There are several other WS medallions though (see pic below of medallions copied from the internet). My understanding is that some British sawmakers used the WS medallion on their saws, and some...

Read this entry »


View Andy's profile

Watch Box #7: OOPS!!

02-02-2012 05:26 PM by Andy | 22 comments »

This is why its been awhile since my last post. One of the problems with shaping wood to this extent is any flaws show up. Figured Bigleaf Maple, aka Western Maple, Oregon Maple, Acer macrophyllum, can have pits, bark inclusions, etc… Well, I found a few during the final shaping. I knew I was getting pretty close to maximum depth in one corner, but I couldnt leave that little black spot glaring at me. Then I was all the way through and exposing the bloodwood below, nothing ...

Read this entry »


View Andy's profile

Watch Box #6: Handle replaced, shaping started

01-11-2012 12:07 AM by Andy | 27 comments »

The handle.I did not like how the handle was looking, it appeared to lack any of the swirling grain that the top inset panel has. That happens sometimes after shaping, the good stuff ends up on the floor. Also… if you look close, you will notice in the picture below that I sanded too deep into the right corner of the handle and exposed the spline! Oops! So I made a new one from Black Palm Wood, a first time for me. The black color ties in with the Wenge corner splines, plus I love ...

Read this entry »


View Andy's profile

Watch Box #5: Hinges, Handle, Dividers

12-30-2011 05:17 PM by Andy | 11 comments »

After glueing in the medallion, I went ahead and sanded it flush with the lid. I did this to be sure it looked ok. I was worried about chipped out areas below the rim showing up after the sanding and it would be much easier to replace the panel at this stage before the entire box was shaped. It would make aligning the jig for recutting the recess less of a nightmare. But it looked fine. The handle is a piece of cut off from the Maple medallion. I simply slotted a mortise in it and the lid ...

Read this entry »


View Andy's profile

Watch Box #4: Glueing in the medallion

12-28-2011 02:42 AM by Andy | 13 comments »

This shows the medallion getting glued in place. I decided to do a loose fit between the medallion and lid on this one due to the fact that I just couldn keep the bloodwood from chipping out even with a new cutter and climb cutting. I have done this before, filling the gap with black epoxy for a shadow line effect. I am using spacers to even out the gap. Before fitting the medallion I had ran a router around the inside of the box and cut a 3/8” x 3/8” rabbit for the lid to ...

Read this entry »


View Andy's profile

Watch Box #3: Fitting the medallion

12-28-2011 01:47 AM by Andy | 7 comments »

I cut the lid a little oversize and made a jig to route out for the maple center panel (medallion). And after. I always make a test piece to size the real insert to. And here is the maple insert prior to rounding the corners which I do by eye on a disc sander and final fit with a sanding block a little at a time. Stay tuned

Read this entry »


View NormiteLou's profile

Router Templates

07-20-2007 11:03 PM by NormiteLou | 9 comments »

Hi All, Template Master is a new product I have developed for making Ultra Precision Tiles called Tessellations.Using the Template Master system, Tessellated Tiles and Borders can be cut in just a few minutes each.A typical 25” diameter 3/4” thick Floor Medallion (as shown in the introduction video) can be cut out, Routered using Template Master , assembled and glued up in less than 3 1/2 hours.Disclaimer: Of course...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase