I’ll take you through the steps I used to build my router guide for my wood lathe. It is essentially a box with adjustable sides and top which has a slot to guide the router bushing. It is made from 5/8” plywood, clear Lexan, Steel and aluminum.I started with a 11.5×11.5 bottom and cut rabbets on both sides on the table saw and made a cut out for the tail stock. The sides were glued in place held square by a couple scrap blocks. They had T nuts installed for the adjustment ...
A few months ago I bought two nice pieces of highly figured maple. 8/4, 9” wide and about 4’ long. And the best part… I got it cheap. So it has been in my shop while I sat around trying to decide what to do with it. I made up my mind. About 16 months ago I made a spice cabinet out of pine and dyed it to look like walnut. I love it, loved everything about it. But I want to make another one, a better one, one from awesome wood. So, thats what I am going to do. This is...
Recently I posted a video covering common woodworking joinery ( http://www.youtube.com/watch?v=zqXLYe783qw ) with the help of a few friends. In that video I talked to you all about making finger joints on the table saw and showed you a finger joint jig in the process. Well as I promised, here is the complete build process of that Jig. Table Saw Finger Joint Jig Also a little reminder about the 2nd Annual Whirligig Wars. It is almost here!! The event Runs from July 10 –...
I’ve had a kind of crappy blue plastic borg sanding block for some time, and I’ve been lazy and switched out the paper. I don’t use it too often, but its finally given up the ghost and won’t really stay closed any more. I decided to make myself some proper ones with a nice cork backing. Here’s the original borg crappy one.. The one thing I do like about it is that it is sized such that you can quarter a regular sized sheet, and they fit the sanding bl...
Welcome back and again sorry for taking so long to get this post out. After my hand healed I was really backed up on some other projects. I’m almost caught up and will post some of those projects on my page in the next couple of days. When we left off we had all the sanding done and are ready for staining and finishing. I’m making two of these frogs, one that will need staining and one out of exotic wood so everyone can participate in this project. We will go over staining next. I’m...
The 60 degree band saw sled as seen in the woodworking video is made from scrap. It took 15 minutes to build from scrap material. As you can see, it is used when cutting small wood pieces for wood inlay banding & parquetry. What kind of band saw blade is being used? ...Wood Slicer – 1/2”, skip tooth, 3-4 TPI. It provides an excellent cut. Can a 60 degree sled be used on the table saw? ...Yes, of course. In fact, my shop is equipped with one as well. Why do you use ...
Hey everyone…A while back I built a hold’em poker table for a friend of mine and recently I was invited to a game at his house. When he brought out the poker accessories he had these real nice clay poker chips in a metal briefcase. I thought how nice it would be to have some wood trays that matched the table. I remember seeing an article in a Woodcraft magazine (Mar ‘07) by Marc Spagnuolo AKA” The Wood Whisperer” for some nice wooden chip trays. I dug up the ar...
When I ordered the BenchCrafted hardware I also ordered the hardware for the Moxon vise. Not only was I inspired by BrandonW’s bench but also his Moxon vise. So, it has been sitting in my shop for about nine months. Brandon’s Moxon Vise The plan is to make a Moxon Vise Bench-top Bench because when I doing fine work I find myself slumping over for extended periods of time. That kind of zaps the fun of it after a while. Furthermore, I admit to being spoiled when comes to h...
I have been working on a project in Cherry and before I finished the desks I decided to try out some of the General Finishes Dye stain but on the scrap test pieces the blotching was driving me nuts. I came to this site and tried all the suggestions until I came across the discussion proclaiming that Charles Neil’s pre stain conditioner was the way to go. Bought some, tried it and still had minor blotching but it works well. Watching his video he said it was a water based PVA enhanced pro...
Creating Wood Inlay Bandings...A Step by Step Process #7: Wood Inlay Banding – How to Make the Square Pattern
To learn more, read the following tutorial. Wood Inlay Banding – How to Make the Square Pattern ............................ The Apprentice and The Journeyman Learn more, Experience more!
- My Journey As A Scroll Saw Pattern Designer - 1367 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- Just for Fun... - 84 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1390 entries
- frank - 417 entries
- degoose - 393 entries
- dbhost - 389 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- mafe - 228 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 190 entries
- Rustic - 185 entries
- Chris Davis - 183 entries
- shipwright - 180 entries
- BritBoxmaker - 166 entries
- PurpLev - 163 entries
- stefang - 158 entries