Updated 1/16/12 This is where you need to decide how you want to open your box. I mentioned at the outset about some of the different boxes I have made and how they hinge differently from one another. All are good, but you may have a preference in style or it may be your ability that decides for you. The pin hinge is what we will mainly be focusing on and was used on this box. Chapter 10 will discuss this style. The Deco box uses a standard brass butt hinge with a stop stra...
Here is a quick and fun Project, A Brain Teaser.. This is the first video of the new Weekly videos I will be posting Every Wednesday!!
Kitchen Treasures #1 Making the Celtic Knot Rolling Pin #4: Glue Up and Trimming The Blank- The Final Steps
Before starting this section, I forgot to add to pix into the previous post. This is the spacer strip used to reposition the blanks for the second cut. The spacer goes between the blank and the fence. This shows the blank seated against the rear stop and the blank is labeled to assure it is not reversed during the various cutting operations. I found it easier to glue if I oriented the blank with the diagonal cut facing up. I use an old restaurant cutting board as a gluing wor...
First of all let me say that this is the first hand plane I have ever made. I looked at some plans to get the general idea, but basically I am making it up as I go. There are things I did wrong but I will be able to fix them. I saw this type of sole on some planes in magazines and always wondered how they did it.It took me a while but I figured it out. Simple once you know how. I got ahead of myself didn’t get started taking pictures until later so I kind of went back over some th...
Oops! began as an idea about outside the box hinges. I’ve always liked the “box on stand” idea but had never tried one so that sort of fell into place and one of the first ideas I had about box decoration was a “spill” pattern. I sketched these on a bit of paper at the kitchen table one day and it was left there. Last December I restored an old ShopSmith 10 ER and had been wanting to see how good a tool it really was and what kind of precision I could achieve...
This Parquetry panel is an insert for a conference table. This is the companies logo, It’s an abstract design of an Eagle. The panel size is 24” wide x 54” long. This was a very fun project, it took me around 32 hours to draw, cut, glue, and stain and finish. I used the “The Window Method” because of the long straight lines and the geometrical shapes. It’s much more accurate this way. If I was to used a scroll saw it would be very hard to keep the lines straight. 1...
Here is the how-to video on hollow form turning: Trifern Hollow Form
The following is an addition to The Apprentice and The Journeyman woodworking video series, Let’s Build. The dedicated dado sled for the table saw is a highly versatile woodworking shop fixture that can expand the woodworking approaches used by many woodworkers. Dado blades are used on the table saw instead of a typical saw blade and the dado blades are often said to be “stacked.” This term implies that the dado blades, chippers, and shims are combined to create a cert...
Finally I got it done and shipped it off to the customer. He wont get it in his hands until next week, so I will post his impressions when I hear back. I hope its what he wants!!! TIP:Some of you may know about this but many will not. This is my secret to quickly fine sand the box prior to spraying lacquer. I hand sanded down to 220 and then I finish up with green nylon pads. These were bought at the local dollar store. Guess how much? Thats right, a whole dollar. You can buy similar pads ...
Until recently my lathe experience has been 50 or so pen/pencils, a few miniature goblets, and a couple small 5 inch bowls over the past few years on a Jet mini lathe, enough to want to try other lathe work. This past fall I was fortunate to have the opportunity to acquire a PM 3520B, but due to other work and priorities I’ve not had a lot of time to use it yet…and that’s “killing me”. So this blog documents what I consider my first significant lathe project. Recently a partially segmen...
- My Journey As A Scroll Saw Pattern Designer - 1542 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 94 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1567 entries
- frank - 417 entries
- degoose - 394 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 269 entries
- William - 258 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 188 entries
- Rustic - 186 entries
- Chris Davis - 183 entries
- BritBoxmaker - 181 entries
- Smitty_Cabinetshop - 170 entries