While planning my first veneer marquetry experience I was a little worried about using hot hide glue to fasten the marquetry to the box sides of my project. I worried that the glue would cool too quickly before I could get it into the veneer press. I had read an article here about making your own liquid hide glue that could be used at room temperature and which had a very long open time. Realizing that this would eliminate any risk of the glue setting up too quickly before pressing I decid...
So Patrick did veneer the column.He first put the veneer on an kraft paper to hold the fiber ni place, we were not sure this thick veneer will like the bending. The article can be found there http://www.oldbrownglue.com/articles.html What you see here is were the seem was made, on the overlap, using a veneer saw then using the reversibility of the glue with an iron to finish the glueing. It cleans easily enough with water I have been careful enough to mark where the ring inse...
We have been hired to make a dining room table from a 30’s model and slide it on the Biedermeier side. This is not our usual traditional furniture making but it is also a nice change in the usual styles we work on. We started with a simple design to show the overall idea Brick laid apron in pine for a light top Poplar “plaque to glue under the top. it will host a metal plate to bolt the lower part to the top The base is made out of beech, for an heav...
Answering the question, vacuum bag veneering with Old Brown Glue, The liquid hide glue If you have any questions, let us know.
Answering the question – veneering with Old Brown Glue Let me know if you have any questions
Yesterday we started a new series on hide glue, liquid hide and here Old Brown Glue in particular.We will try to post a new video a week in the question and answer format. Let me know if you have any questions that we can answer, and let me know what you think so I can improve the format or the filming. Let me know if you have any questions! Cheers
Complicated Face Frame The Dr. White’s chest is a combination wardrobe/chest of drawers and has a complicated face frame. There are eight mortise and tenon joints, ten dovetail joints, and one half-lap joint in the frame. I cut the dovetail joints with my Leigh dovetail jig. Watch this video to see how I cut the female portion of the face frame dovetail joints. I cut the male portion of the joint using the same jig in the vertical mode and the bit set at the same depth. NOTE: Chip out...
Jointly Epoxied ….white oak bleeds moon red,my heart bonds with your passion,jointly epoxied….—by flp —————————————————————————————————————————————————————...
- My Journey As A Scroll Saw Pattern Designer - 1370 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- Just for Fun... - 84 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- Sheila Landry (scrollgirl) - 1393 entries
- frank - 417 entries
- degoose - 393 entries
- dbhost - 389 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- William - 258 entries
- mafe - 228 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 190 entries
- Rustic - 185 entries
- Chris Davis - 183 entries
- shipwright - 180 entries
- BritBoxmaker - 166 entries
- PurpLev - 163 entries
- stefang - 158 entries