While this is the beginning of my construction blog for the V8 Degree bench, I’m not actually going to get into the build just yet. There are a few more features that I didn’t want to clutter the project post with and I’ve added a couple of demo videos on the vices. I thought it would be best to start with a full view of the bench and its operational features first and get into the construction process in the next segment. This photo shows the dog hole inserts that hide a...
Finally, a package with my vintage vice screw (thanks Smitty) And maybe some of you remember some wood I got. It was 2” thick, about 9” wide and consisted of oak, birch and polar. I’m not sure what it was cut for, but it was headed for a fireplace. It has been outside for a while, so it has a rustic look. Well one of the pieces of oak seemed to have Leg Vice written all over it. So, grab the #6 and start to straighten it up. Make i...
Ever since I’ve seen the wheel drive like the bench craft I thought it would be pretty cool to have, as an upgrade to my leg vice. But I’m more of a vintage guy, so something that new and shinny wouldn’t fit the decor of my shop. Plus, at over $300, I find it hard to justify. So as I saw wheels in flea markets and antique shops I’d stop and look. Most were way more than I thought they were worth, and I even bought an old tractor steering wheel, but it just didnR...
I’ve been working on this bench for I guess 2 months now on my days off. It’s southern yellow pine. I dug around the shelf for at least an hour picking out boards at Home Depot, but could not find any without knots. Not one. Must be an Alabama thing. I decided that a wood screw was in order for my phantom vintage bench, and found one at Lake Erie Toolworks. I didn’t want to invest so much into a vice screw, but I could not find a vintage screwbox on e...
Ok, so last time I had finished my pegboard cabinet and was getting ready to start on my vertical drawers, or sliding book shelves, sliding cabinets, whatever. I haven’t quite gotten started on those yet. I was getting ready to. I got a few of the boards cut and was getting ready to start building them when I realized I didn’t really know how. I started looking around at the different types of wood joints and finally settled a couple I’m going to use for good sturdy sliding ...
I’ve been doing a bit of repetitive hand cutting (dovetails) in my leg vice (or vise if you prefer) lately and while I am very happy with it in general, I guess the one drawback has always been that you almost need another hand for the wedge sometimes. It became enough of a frustration this week that I gave it a little thought and came up with this solution. It’s very simple. I just inlayed a rare earth magnet into the sloped face of the wedge hole and a strip of steel (straigh...
In between jobs I have been building a new work bench milled from 8/4 and 12/4 maple hard and soft. The top is 4” thick. 24” wide, 6’6” long the legs are 4”X5” and the bench is 33” high which is at the point where my wrist makes a crease. The wagon vice is from Lake Erie Tools as will be the leg vice. I am building it by hand with no power tools at all, Whew! I still need to mount the leg vice after all the stretchers are cut, 16 mortise & ten...
My friend and I are in the planning stages of doing a joint, side-by-side build of some new workbenches. This will start with the logs and hiring a guy with a woodmizer to mill the timber in to boards. It looks like we are going to be using red oak, as we are able to get more than enough at the going price of fire/cord wood, then paying $.30/bd ft. to have it rough sawn. So, this won’t begin till next winter after it dries. Here are a couple sketches. No secrets here on the des...
Here goes…. Traditional work benches (roubo for example) are out dated. I know, heresy. But it’s true The reason they made those crazy over sized legs and joints was because they didnt have sheetgoods back then and they needed to over build them to deal with the lateral and horizontal force they experienced. It is my opinion that pine 2×6’s and 3/4 ply MORE than cover any of the structural needs of a work bench. So the next big argument FOR traditional w...
- My Journey As A Scroll Saw Pattern Designer - 1546 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 95 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1571 entries
- frank - 417 entries
- degoose - 394 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 271 entries
- William - 258 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- shipwright - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 188 entries
- Rustic - 186 entries
- Chris Davis - 183 entries
- BritBoxmaker - 181 entries
- Smitty_Cabinetshop - 172 entries