LumberJocks

Woodworking blog entries tagged with 'laminate'

  • Advertise with us
View RaggedKerf's profile

My First Workbench #33: Leg Vise Chop Redux

08-23-2013 09:44 PM by RaggedKerf | 2 comments »

Okay, so if you follow this blog, you’ll know that last year I built a leg vice and attached it to the workbench I built over the summer. The chop on this vice was simply two pieces of 3/4” pine, about 6” wide, glued together and shaped (with some crude tools I had at the time and zero knowledge of what I was doing). Then I carved my initials and the year of it’s construction (2012) into it and made a nice little handle out of poplar. Well, it works. ThatR...

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #3: Glueing up pairs of boards and then glueing up quads

02-17-2015 02:44 AM by ruddhess | 2 comments »

This is the first two boards glued together the night before this picture. I have taken the bolts out and everything looks solid. Time will tell. This first one was probably the worst for glue coverage as I was in a hurry – it has been too long since I glued boards together. I keep thinking that if I didn’t hurry, the glue would set up and I’d have to do everything over again. But I think it will still be OK. I used plenty of glue on both sides and the only part I’...

Read this entry »


View CaptainSkully's profile

Arts & Crafts Dining Room Set #20: Joinery Shortcuts

08-21-2010 04:12 PM by CaptainSkully | 1 comment »

I was able to squeeze another good day in the shop around work. I ran off to buy some more oak, then got home and planed enough of it down to glue up the stretchers/aprons for the table ends. While the laminations were cooking, I decided to give the BeadLock Pro a whirl. Having made integral tenons with chiseled mortises, and loose tenons with the router, I have to say this method is considerably easier and faster. First, I was able to cut off the parts to their finished length, without...

Read this entry »


View RobertHorton's profile

Pangapanga sideboard #1: Top laminates and curved inlays

11-04-2009 06:29 AM by RobertHorton | 1 comment »

Used the old trick of a straight board and a router to get a glue-able edge on the Panga laminates for the top. One set is gluing already and we’ll move on to the next tomorrow. Pulled open the form and revealed my curved inlay stock for the top also. I was worried that the aluminum would be too springy, but the glue held just fine. I only need to get two arcs out of this, so there’s plenty of room to goof the first cut.

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #2: Drilling holes for bolts and all-threads

02-15-2015 05:21 AM by ruddhess | 0 comments »

Using some 3-1/2” bolts to glue up two boards at a time. It is easier to keep everything square and straight this way. Also there’s no rush just gluing two boards together. The holes are 5/8” so that when I get ready to glue up the 6 sets of paired laminations, I can use the 3/8’ threaded rod – hopefully the holes line up well enough.

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #7: Remainder of yellow pine lumber for workbench

03-04-2015 06:38 PM by ruddhess | 0 comments »

Here is the remainder of the yellow pine that I need for my workbench. I had decided to give this thing legs and a skirt (hmm, sounds bad I know – hey maybe it’s a Scottish bench? LOL). The 2 X 12 was for the skirts on the front and the back, and the 2 X 8’s were for leg stretchers. I had 6 pieces of center ripped 2 X 10’s left over from making the top that I could use to make the legs. Still deciding whether to make a regular workbench or stay with my original plan of...

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #1: My first "benchtop"

02-13-2015 02:20 AM by ruddhess | 0 comments »

Beginning to make a Japanese style planing beam/board. 6 boards from Lowe’s – 2 X 10 X 12’s cut in half and staked up on my old sawhorses. I used a 1 X 2 “select” pine as a straight edge – screwed to the 2X with drywall screws as a guide for my circular saw. Set the depth to leave a wafer thin “bridge” on the very bottom so I didn’t cut into the board below. Worked very well. (Bit of a “mis-start” on the first board....

Read this entry »


View ruddhess's profile

Southern Yellow Pine Work Surface (workbench) #5: Getting Close to Full Width

02-22-2015 02:53 PM by ruddhess | 0 comments »

I ended up gluing inside my apartment where it was warmer. Ice and snowoutside. It is wide enough now that it won’t fit inside the glue box anyway. All 12 boards glued up. I think that I will add 2 more to make it 21” wide. Finally got a decent picture of all 14 boards glued up. Now to find help carrying it down to the garage when the weather turns nicer. It weighs over a hundred pounds. Not bad.

Read this entry »


View TrentDavis's profile

Table Saw Modifications #5: Router Table Enclosure: Part 2 - Laminate

04-14-2017 01:31 PM by TrentDavis | 0 comments »

This is Part 2 of a tutorial for building an enclosure for the router lift I added to the extension table on a SawStop table saw. Check it out here:http://trentdavis.net/2017/04/14/table-saw-modification-router-table-enclosure-part-2-laminate/

Read this entry »


« prev 1 2 3
29 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com