Candy, this blog’s for you!!!!!!!!!!!This is the process I use to turn a scoop from a wood blank on the lathe.I start by defining the volume needed in the the scoop. The formula is Pi x R squared x depth I planned on a 1/2 cup scoop and the volume of 4 oz is 7.218 cubic inches and I want the inside to be 2 5/8” So the formula is 3.1416 x ( 1.312) squared x depth = 7.218. The depth figures out to be 1.33” I start by drawing it out and then adding scrap wood in the area...
We have two, large juniper slabs for sale in Overgaard, AZ. The largest measures roughly 34 3/4” x 63” and is 3” thick, we are asking $225. The narrower of the two measures about 21’ across the middle x 57” tall and is 2 1/4” thick, and we are asking $150.We have more slabs of comparable size that we are willing to sell, and more pictures are available upon request.
Progress on the stump is going well. For the past week, every evening rather than working out in the cold shop, I have had a comfortable seat on the couch inlaying turquoise and copper. At first I only planned on doing a few inlays, but as the cold weather continued, so did my inlays. This project should be pretty awesome when I’m all done!! My uncle made me a really handy stone crushing tool that takes the mess out of smashing up turquoise into small pieces and dust. ...
Evolution of a stump: From natures sculpture to mine. #2: Sanding, burning, more sanding.....and more sanding!!
Working through the grits of sandpaper is important. I feel like I could utilize some advantage if I included a couple more “in between grits” from my typical strategy, but sandpaper costs a lot!!! I started this piece with my chainsaw, roughing out the size and shape, cutting a “flat” top and bottom….then moving to my angle grinder with my favorite shaping tool attached, the Holey Galahad carbide disk. After the shaping is mostly complete, I move on to the o...
My uncle was needing to expand his horse pasture, and thankfully I just happened to be there the day he was going to push this old tree down with a tractor and throw it in a slash pile. Just an ugly old rotten tree to him, but I saw it different. “HOLD ON Uncle Joe, let me get my chainsaw and take this tree out for you.” “What are you going to do with that”? he says…..well, just wait and see. A couple of hours later, using a chainsaw and...
Lots of grinding done,.....lots of grinding to go!!
Here is what I got done last night. The top is very close to done being sculpted down into the base, and the “ribbon” sculpting is looking pretty cool. Its a pretty stable table already, not much more to do for leveling it all out. So far I’m pretty happy with it.
I say this with every project, and I’ll say it again with this one….this is my favorite!! This table is going to stretch my sculpting skills to new limits. I am going to try sculpt the top of this table down into the base limb so that it will provide good support, and also sculpt the limb into a twisted “ribbon” shape. These photos show the rough idea of how the pieces will sit with each other, and the start of sculpting the “ribbon” base limb. The top will...
Well, its all together and ALMOST finished…..I ran out of teak oil before I could step back and say “DONE”, and all the stores were closed by this time. I’ll have to finish it up tonight. This will be the final blog before I post this as a project. Overall, I’m very happy with it, and have gotten very positive comments on the design. I rushed the final assembly more than my usual critical eye would allow, (which means I cut corners on finish sanding ALL surfaces...
I will have quite a bit of cut off scraps from some nice juniper lumber. It has been dry for about 14yrs. They are planed to about 5/8” thick, and will be anywhere from 6” to 20” long. I was thinking about bundling up packages of and selling them to interested lumberjocks. If interested, please send me a message with ANY reasonable offer that would be worth taking the time to package and ship these out to you. I just cant bring myself to throw the scraps away knowing they co...
- My Journey As A Scroll Saw Pattern Designer - 1598 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- Just for Fun... - 96 parts
- A journey into the workshop. - 89 parts
- Daily Update - 87 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- ScrollSaw Information and Resources - 68 parts
- Sheila Landry (scrollgirl) - 1623 entries
- frank - 417 entries
- degoose - 397 entries
- dbhost - 390 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- Martin Sojka - 296 entries
- mafe - 279 entries
- William - 258 entries
- Betsy - 221 entries
- shipwright - 218 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 199 entries
- stefang - 198 entries
- Rustic - 188 entries
- BritBoxmaker - 187 entries
- Chris Davis - 183 entries
- Smitty_Cabinetshop - 176 entries