LumberJocks

Woodworking blog entries tagged with 'joining'

  • Advertise with us
View jfk4032's profile

Tumbling block cutting board techniques, lessons learned and tips for cutting and assembly

01-13-2014 02:32 PM by jfk4032 | 8 comments »

After looking through some other blogs here on LJ and watching some Youtube videos I thought that the tumbling block cutting board was something that looked challenging, cool and something I wanted to try. I learned some good ideas from these other blogs and wanted to share some of my experiences having now made three of these, my setbacks and discoveries to better produce these tumbling block patterns. I purchased a Wixey digital angle gauge as it looked like you really needed to be accu...

Read this entry »


View WoodJediNTraining's profile

Make a Folding Out Feed Table for your Table Saw

02-20-2013 05:22 PM by WoodJediNTraining | 16 comments »

This Week I show you how to make a folding out feed table for your table saw. This design was based after an article and plan found in a 2009 issue of Woodworker’s Journal Magazine. Originally the plan was designed for a Cabinet saw with a Biesemeyer Fence System, so I had to make some slight modifications for my Porter Cable Saw. In this 3 part video series I show you a step by step on building this project as well as talk about the modifications I had to make. The Article and plans ca...

Read this entry »


View Andy's profile

"Art Box" Tutorial #9: It all hinges on this.

07-17-2009 03:53 PM by Andy | 8 comments »

Updated 1/16/12 This is where you need to decide how you want to open your box. I mentioned at the outset about some of the different boxes I have made and how they hinge differently from one another. All are good, but you may have a preference in style or it may be your ability that decides for you. The pin hinge is what we will mainly be focusing on and was used on this box. Chapter 10 will discuss this style. The Deco box uses a standard brass butt hinge with a stop stra...

Read this entry »


View scrappy's profile

Making a Wood Bracelet with Scrappy #1: Step #1 Getting Ready/Choosing your Wood

09-04-2011 08:08 PM by scrappy | 8 comments »

Hello all,I have been asked to give a class on making a wood bracelet similar to this one. http://lumberjocks.com/projects/18322 I want to point out that we will NOT be using the special jig I made. I have a different way to get the same results which does not require each of you making a jig. Part #1Getting started and choosing wood. Step #2Preparation off wood and cutting notches. Step #3Drilling holes and shaping. Step #4Finishing and final assembly We will begin be goin...

Read this entry »


View Bob Simmons's profile

Let's Build a Dedicated Dado Sled for the Table Saw

08-15-2010 07:06 PM by Bob Simmons | 6 comments »

The following is an addition to The Apprentice and The Journeyman woodworking video series, Let’s Build. The dedicated dado sled for the table saw is a highly versatile woodworking shop fixture that can expand the woodworking approaches used by many woodworkers. Dado blades are used on the table saw instead of a typical saw blade and the dado blades are often said to be “stacked.” This term implies that the dado blades, chippers, and shims are combined to create a cert...

Read this entry »


View shipwright's profile

Creating Oops! tutorial

10-02-2010 06:33 PM by shipwright | 13 comments »

Oops! began as an idea about outside the box hinges. I’ve always liked the “box on stand” idea but had never tried one so that sort of fell into place and one of the first ideas I had about box decoration was a “spill” pattern. I sketched these on a bit of paper at the kitchen table one day and it was left there. Last December I restored an old ShopSmith 10 ER and had been wanting to see how good a tool it really was and what kind of precision I could achieve...

Read this entry »


View shipwright's profile

Facets, the Next Logical Step #1: How hard can it be to make a Dodecahedron?

12-12-2010 03:37 AM by shipwright | 16 comments »

The next box in the series Oops!, A Llittle Cabinetree, and now Facets is on the build. It had to be started because I’ve been obsessing too much on the finish of Cabinetree and in order to amuse myself between coats I had been so bored I had started making micro plywood and then micro boxes and banding. It had to stop.So the other day I started to think about what the next logical step would be keeping the theme and some of the aspects of the others but going a very different direction...

Read this entry »


View degoose's profile

Just a small how to.

09-12-2009 10:46 AM by degoose | 24 comments »

This board is not part of the 150.. I showed one of the 150 to a friend and she wanted one but a little larger,This is the way it was made.Cut some bits of board. NGR SA TBDress all sides.This is to see the way it will look with the stripe. Cut all pieces to 250 mm.Join the NGR and edge with TB on one and SA for the other.Glue a sacrificial board to the SA prior to cutting the arcs.This is the arc cutting jig.. a slight variation on the patron jigSet the stop with a nail… high tech I kn...

Read this entry »


View brklnguy's profile

Building a roubo workbench in my apartment #1: Making the top

02-15-2010 07:04 AM by brklnguy | 26 comments »

I never want to hear anyone complain about their shop… anything has to be better than a tiny living room in a 400sqft apartment. This is my first project with hand tools. I worked as a cabinetmaker for 6 years, and then moved to NYC 3 years ago and changed careers. I’ve been wanting to get back into building furniture, and after a few months of reading everything Chris Schwartz has written and pretty much every other hand tool blog on the internet, I feel like I know everything...

Read this entry »


View Bob Simmons's profile

A dedicated Mitre Sled for the Tablesaw

07-04-2010 05:52 PM by Bob Simmons | 21 comments »

Has there ever been a time that you’ve struggled to cut a perfect mitre joint? Believe me, there’s no need to feel alone. All of us have had our challenges with the mitre joint at one time or another. So, let’s say that we want to build a woodworking project like a picture frame and we are looking to create four dead-on mitres joints. What’s going to be the woodworking tool of choice? We could use a chop saw or a mitre saw for our joinery. We could use a fine handsa...

Read this entry »


« prev 1 2 3 4 5 6 ... 104 next »
1035 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase