LumberJocks

Woodworking blog entries tagged with 'hepplewhite'

  • Advertise with us
View John Fry's profile

A Hepplewhite style Federal game table in six days, PIX.

09-18-2008 02:49 AM by John Fry | 13 comments »

A while back I posted a project that I did in my shop in California with my woodworking friend Jack Hutchison from Houston, TX. Here is that post: A Krenov Inspired Cabinet on Stand in Six Days We completed that cabinet during a six day visit by Jack. Our agreement was that at some future date, I would go to Houston and we’d do another six day project in his shop. So….I arrived at Jack’s and we completed a much more complicated piece in another six day time frame and here it is………....

Read this entry »


View davemoorefurniture's profile

Check out my latest vid

03-30-2010 09:40 PM by davemoorefurniture | 13 comments »

I am new to lumberjocks and was recommended by a current user. Check out this video I made that shows how to use hand tools to inlay a design in stringing. http://www.youtube.com/watch?v=BUSfz3n7nYE

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #3: Lay-Out & Rough-Cut

12-10-2016 11:39 PM by Ron Aylor | 3 comments »

 It finally stopped raining! I shouldn’t complain because we actually needed the rain, everything had become so dry. But, at any rate, the sun is out and I can see all the way to the back of the shop. So it is time to get this little stand laid-out and rough cut. I glued-up the top a few weeks ago. I think the Ambrosia maple looks awesome … you? It is currently over-sized by a few inches, I’ll cut it to fit once the base is completed. The lumber I get from Suwanee Lumber ...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #2: First Things First

12-05-2016 08:20 PM by Ron Aylor | 2 comments »

 It’s been raining for a day or so here in Lilburn, and as a result I haven’t had much shop time. Too dark. But, I’m still moving forward with my little Hepplewhite stand. Given that the original stand was built 19 years ago, I thought it prudent to measure all the parts, as I did not measure anything back then. I simply established a comfortable height and filled the space where she was going to rest. Unfortunately, I kept no notes; at least I cannot find any, other than...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #4: A Proper Edge

12-18-2016 04:50 PM by Ron Aylor | 2 comments »

 Before jumping into the mortise and tenon joints I thought it a good idea to make sure my chisels have a proper edge. For this project I need a 3/8 mortise chisel, a 1/2” firmer chisel for the half blind dovetails, and a 1-1/2” bevel edge chisel for the tapered legs. A proper edge is actually quite simple. You need but two intersecting planes. Generally, the smaller the angle between the two planes, the sharper the edge and easier the cut. The smaller the angle, though, the less force it ...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #1: What's Wrong With This Picture

12-03-2016 09:10 PM by Ron Aylor | 15 comments »

 So, my bride comes to me this morning asking, “what’s wrong with this picture?”   Realizing that it had been quite a few years since my first Hepplewhite stand, I committed to build another to even out the look of our bedroom. The first stand, built in 1997, has red oak legs, hackberry sides and drawer font, and a sassafras top. It was finished with shellac and beeswax. The top has been re-waxed several times over the years and is in need of a touch up. As to the new stand,...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #5: Mortises ... Finally!

12-28-2016 09:31 PM by Ron Aylor | 4 comments »

 After but a few distractions, my head is now back in the game! I spent a couple of hours squaring up the cherry legs with my No. 4 bench plane and No. 3 coffin smoother …  ... turned out okay … nice and square … I never see light under the square when I point it to the rear of the shop (hmmm) ...  ... and no twist … that I can see anyway!  Once all squared-up, I mark off about an inch of waste at the top end of each leg and lay-out the various mortises for the drawer ...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #6: Frame Members Sized for Tenons

01-16-2017 05:26 PM by Ron Aylor | 1 comment »

What crazy weather we’ve been having in Atlanta. One week there’s ice all over everything with temperatures in the teens, and the next week we are all running around in shorts enjoying temperatures in the 70s. It’s a wonder we’re not all in the hospital! Taking advantage of the warm days, I decided to put in a few hours cutting the frame members to size and forming the tenons. First, I ripped the front, sides and back to the required 4-1/2” width.  After jointing th...

Read this entry »


View Ron Aylor's profile

Hepplewhite Stand #7: Tapering the Legs

01-21-2017 12:33 AM by Ron Aylor | 1 comment »

 With the tenons cut and fitted to their respective mortises, it’s time to taper the legs.  I want the legs to taper down from 1-1/2” to 1-1/8” starting about 5” from the top. I marked an 1-1/8” square at the bottom of each leg.   By the time I marked all the legs it started to turn dark … a storm was blowing in …  ... and the shop quickly became as black as the inside of a cat! ... better call it a night!  After a good night’s rain, I finished defining the 1-1/8” s...

Read this entry »



DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com