After showing some of my boxes in “Projects”. I have received some inquiries about the installation of the barrel hinges I sometimes use. I hope this helps for some of you. I know it will be overkill for many of you, so just use what you wish. With any type hinge, the layout is critical. These hinges are simple to install, but you must get your holes in the right place. If you don’t, I can assure you , you will not like the results, and you will not be able to go back and...
I had an idea of how to make T-track on the cheap. I shot this video with my phone so it is not the best but you get the idea.
I continuing to improve my workshop, removing rust, organizing my tools, and building cabinets and organization fixtures. This weekend I finished up my new hardware cabinet. Last weekend I build the box: Cut it in half: Turned the front of the box into doors: It was when I got to this point in the project, that I discovered that the magnets and magnet cups I purchased were not the same size. I got online and order some smaller magnets to fit the cups I had, and larger cups to ...
I filmed the build on my YouTube Channel. Please check it out! http://youtu.be/qDOujXINlE0 Typical washer and dryers are lower to the ground. You can buy stands for each unit for around $150-250. I decided to build mine and incorporate stylish hardware, larger drawers, classy hutch, and a special detergent feature. The build consists of MDF, Poplar face frames, brushed nickel hardware, full extension drawer slides, Oil based primer, and white paint. Primary construction method was ra...
The Doors Last time I glued up the door fronts: I spent some time fitting the doors with a plane: And then I passed them through the drum sander to flatten them: This little marking jig came with the hinge drill bit I bought: Drilling the holes for the hinges: Aligning the hinges: The Skinny Door I’ve been going back and forth on whether or not to cover the space where the DVD player shelf is. I finally decided it needed a cover of some ki...
“Lord, grant that I may always desire more than I can accomplish.”Michelangelo…Italian sculptor, painter, architect, & poet. (1475-1564) Enjoy the decorative door knockers from Florence, Italy. Many front doors have knobs, hinges, and knockers of unique design of cast iron and solid brass. It is here that we will feature some wonderful door knockers and one very special solid brass door knob. Florence, Italy is considered the birthplace to the Italian Renaissan...
Now to begin with, this is not woodworking, but does have to do with furniture. I have had many woodworkers that have been curious about blacksmithing and what i do and how I got into it. I never post my smithing projects here just because it is a woodworking forum. However, I feel like a lot of woodworker could create their own drawer pulls out of metal in their shops. You can use a coffee can forge and a vise really. Check out the video and see how easy it is and create your own hardware fo...
I did follow the WoodWhisperer’s plans for the dog holes as well as many of the other elements. I reversed the dog hole jig to make one for the dog block which was canted in the opposite direction. The only thing that accomplished was it kept the 3/8” strip on the movable dog block on the same side as the glue-up. Routing the dog holes went smoothly, lots of sawdust and shavings! Gluing the thin strip to the routed piece with a full length caul. Broug...
When we left subject cabinet, the last part of the build was done, as the upper door pieces were cut and fit and glued up. Stiles ran long on the doors, as Lysdexic correctly pointed out, to prevent spitting of the entire stile while the mortises were cut. So we know the doors needed a trim length wise. What I didn’t realize is how close I had made it re: the rails. You can see in the pics below I had to preserve all of the rail material… Whew… There was ve...
In the process of organizing the shop I had definite need of hardware storage. I had an old dresser that I revamped and used it for the larger parts, but the small stuff was overwhelming. I had 5 generic boxes and bought 5 more plano 3700 boxes to sort everything into. Here’s a pic of the sorting process which took over 9hrs to finish…LOL! It was a long day! Next I built a rack to hold all 10 of the boxes. I used some surplus PT 1×2 stock that I had. Here’s a pi...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 107 parts
- Workshop Development - 107 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 420 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 214 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 194 entries
- A Slice of Wood Workshop - 190 entries