LumberJocks

Woodworking blog entries tagged with 'hand made'

  • Advertise with us
View LastingBuild's profile

Amazing Workbench Build |Hand tool Woodworking

10-18-2018 04:41 PM by LastingBuild | 1 comment »

A few months ago, I posted pictures of my Paul Sellers Workbench and received a really big response. I linked it to my build series on youtube. The series is too long for most people to watch so I condensed it into 5 minutes (over 15 hours of video footage). I hope my video inspires others to build one of their own. This experience has changed my practice of woodworking forever. https://www.youtube.com/watch?v=GzHMfhUK4R0&t=1s

Read this entry »


View LastingBuild's profile

Treadle Lathe #3: Cutting Joinery

10-11-2018 12:52 AM by LastingBuild | 0 comments »

Making progress on the lathe. In the last post, I laid out the ways (the horizontal boards that the head stock, tail stock and tool rest sit on) and in this episode I cut four tenons and two housing dados! This project is definitely taking longer than expected but I’m happy with the current progress and I’m confident it will be worth the effort. Working with oak has been a learning curve in comparison to pine. View on YouTube I can’t wait to be turning wood with a f...

Read this entry »


View LastingBuild's profile

How to dimension lumber with handtools #4: Parallel face and edge

09-15-2018 12:20 AM by LastingBuild | 0 comments »

After establishing the reference face and edge, I use my marking gauge to mark the board thickness using the reference face as the guide. Once I have marked all four sides, I use my jack plane, jointer plane and smoothing plane to bring down the rough surface of the board to my marking lines. Then, I repeat the step for the board width using the reference edge as the guide. Once finished the board was perfectly square. (as perfect as necessary at least). If you would like to watch my video...

Read this entry »


View KelleyCrafts's profile

A couple of tips for turning cast/wood blanks.

11-14-2017 02:50 AM by KelleyCrafts | 5 comments »

If you have never turned a cast wood blank and would like a few tips I wrote a blog post about it. Some of these may seem obvious but to new turners it would be helpful for sure. These tips could be helpful for blanks that aren’t cast wood blanks as well. You can find the blog post HERE. Thanks! Dave

Read this entry »


View JimChrisawn's profile

Handmade and Special Purpose Lathe tools

03-27-2016 07:36 PM by JimChrisawn | 2 comments »

I really enjoy woodworking and especially hand tool and turning. I really like to make small lathe tools for detail work. I use HSS in different sizes depending on the tool I need or want to make. In this picture from left to right, point detail tool, 1/4” point and round nose scrapers, 1/4” round skew, 1/4” double ended three point tool, small Allen wrench hollowing tool, 1/4” fluteless gouge. In this picture from left to right: 3/8” three point tool ...

Read this entry »


View revieck's profile

Building a marking gauge.

12-05-2015 06:31 PM by revieck | 3 comments »

In this video, I build a home made marking gauge from scrap wood. https://youtu.be/m5ehhwZaghU

Read this entry »


View A Slice of Wood Workshop's profile

Make Your Own Drawer Pulls

01-06-2015 10:33 PM by A Slice of Wood Workshop | 1 comment »

Now to begin with, this is not woodworking, but does have to do with furniture. I have had many woodworkers that have been curious about blacksmithing and what i do and how I got into it. I never post my smithing projects here just because it is a woodworking forum. However, I feel like a lot of woodworker could create their own drawer pulls out of metal in their shops. You can use a coffee can forge and a vise really. Check out the video and see how easy it is and create your own hardware fo...

Read this entry »


View piddlinchic's profile

Oyster knives #2: finally figuring it out

07-01-2014 03:37 PM by piddlinchic | 8 comments »

not sure if this link showed up but I tried pasting it from my Facebook page. If not, you can just go to the page. I will be adding more as I finish them. www.facebook.com/piddlinchic I’ve been having fun with these knives. Recycling “trash” has it’s own rewards. I could probably do a better job and save a lot of time by buying steel stock or precut knife blades, but this is much more fun and challenging.

Read this entry »


View A Slice of Wood Workshop's profile

Easy made Router Plane from a pallet

11-12-2013 11:31 AM by A Slice of Wood Workshop | 0 comments »

I have been looking at getting a router plane for some time now. Ebay has great deals, but if you know me you know I like making my own tools. In this video I make my own router plane using a piece of oak pallet, a thumbscrew, wing nut, and an old cheap hex wrench. I opted out of installing handles on this (like most do that are this version) because i liked the feel. I could use my hole hand instead of holding onto some knobs. Hope you enjoy and view the video HERE!

Read this entry »


View CalumetWoodworks's profile

Desert Storm Tank Carrier #2: Tank progress

10-14-2012 07:25 PM by CalumetWoodworks | 3 comments »

Made some progress on the tank. Adding wheels and gluing the turret. Yes it rotates. Since I am painting this for my customer I can use up some of the scrap wood I have laying around. I hope to get the trailer done today as well since the Packer game is on this evening.

Read this entry »


1 2 next »
16 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com