This is the puzzle all cut out and put back togetherNotice I did not even really try to cut my “G” and “H” perfect. You can see where ther is some to be removed also between the “O” and “P”. I would have rather cut this out better but I did not, nor did I notice it till now. In comes “The Cheater” My term of endearment to one of my very favorite tools I own. My very old Delta 1×42 inch belt sander (with a 8 inch) disc sander on ...
This is the way I have chosen to cut this out. First to go is the “O”. Leaving me with with the long “H” which is like the backJust a short tiny cut removes the 1st “P”of the double “P’s” Now I only have the “H” left and the “G” and I can cut them any which way I want to.In the next and last of this much too long series I will be bringing in “The Cheater”
My next step has been taken and that is to cut out all the inside pieces with the starter holes. I have done many of these puzzles and normally I have cut them by simply cutting off a letter at a time. Besides the middle of the A’s and R’s and O’s and P’s a person does not even need to place a starter hole in the other places if you are to cut the letters out one at a time. In the letters L,L,I,G, if I were to have cut the letters OFF one at a time then these inside cu...
This is the plate of my Scroll saw. What I am going to do for this project is I am going to cover it with a couple sheets of white paper and a playing card. I have a couple of reasons for this. First is I don’t want any small pieces I will be cutting to fall through. Which in actuality there is not small pieces per say, rather the little ends of the “puzzle pieces” . The tabs that I do not want to break…..pictureSo this is now taped on the scroll saw table just for th...
This is the plate of my Scroll saw. What I am going to do for this project is I am going to cover it with a couple sheets of white paper and a playing card. I have a couple of reasons for this. First is I don’t want any small pieces I will be cutting to fall through. Which in actuality there is not small pieces per say, rather the little ends of the “puzzle pieces” . The tabs that I do not want to break…..So this is now taped on the scroll saw table just for this proj...
This is one of my personal favorites. The pattern came from Creative Woodworks & crafts March 2000 Special Double Millenium issue and is titled “Red Tailed Hawk.” It was the beginning of my love for doing birds in intarsia. For me these birds are not easy,to say the least and perhaps that is where my love for doing them lies.I LOVE the challenge!!! Matter of fact the first one of this pattern I had done I had the hardest time getting the feathers to line up so much so that I actually ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries