Well, I was getting ready to assemble a 16×20 frame, when I realized that the woman who ordered it needed to give input on the finish. While inspecting it, a piece just fell off with the sligtest tough from my finger. I didn’t think too much about it and threw it somewhere. After showing my wife, her first response was, what happened there? Well, I thought it made it look more rustic, but apparently too rustic because that was the first response of the woman I was selling...
This project is half finished – Literally I mean. I figured since I’ll be working on the drawers, and the toolcart is in the basement it’ll get dirty, and oily finger marks might penetrate the wood and no sanding in the world will take those out, so I decided to finish the cabinet and protect it from the ‘elements’ around…. and boy did I get struck out by one of those elements… but more about that later. And so I gave the cabinet a good sanding wit...
Gorilla Glue has challenged you to build one of your wonderful creations using Gorilla Glue as your main fastener (no metal fasteners). And now you can take a look at 16 creative entries as a result of this challenge. It’s also time to announce the prize winners: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Grand Prize consists of $200 plus 1 of each Gorilla Glue's products and a Gorilla Glue t-shirt: ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 5 runn...
Had another quick chance for some shop time and used that to glue together the fitted carcass. I didn’t want to deal with the glueup the day before (after fitting the dividers) as I knew I would need a peace of mind and ample time to do the glueup properly and not rush through it. And so, I cleared the workbench from all the ‘things’ that always seem to end up on it (how is that always happening?!?) to have use of it’s full length (barely enough) and laid down the c...
In this video, I am doing a small demo on FastCap’s Glü Bot along with Chris. FastCap is a recent new sponsor of ours and we have done a couple of videos showing off their cool stuff. This is the first!
I was able to plane the stock for the shelves yesterday. I glued up a large enough blank for two shelves, then used the fence to cut them parallel. I then used the cross-cut sled to square the other sides. I got to use my Delta new mortiser to make all of the mortises (3 on each side x 4 sides = 12 total). Luckily, they were all 3/8” and had the same offset from the front/back. This meant that with one setup, I could knock them all out. If I had done them with a chisel, ...
There are many parts of this project I do not want to discuss, mostly because they all involve mistakes. With this project I unfortunately made many stupid errors regarding dimensions and process of operations, but in ways that are rudimentary to woodworking. I tried to recover and hide these though thinking about the saying that being a good woodworker is not about making no mistakes, its about how well you can fix the mistakes you make. One of these mistakes came from a lack of room in...
The process continues… Glued it up tonight. I’m glad I could find the generic epoxy syringe at the local big box. I didn’t have time for a trek to Rockler or Woodcraft for a small glue kit. The tip fit perfectly between the fingers and was easy to control the amout of glue dispensed. I’ll be cleaning up the slightly proud ends of the joints tomorrow evening. I hope that goes well considering the fingers are only 1/8” thick. I’m a little worried about tea...
Has anyone ever made or seen a counter top made like an end grain cutting board. I am thinking of trying it. Counter top would be 34 square feet minus the built in cook top and sink. it will be about 4500 square inchs. i would like to make it in a herring bone pattern with 1 1/2×4 pieces. What glue would i have to use? It would be in oak, cherry, some walnut and maple. I figure it to be 1” thick set on 3/4 inch plywood. Any ideas from you guys would help. Or should...
- My Journey As A Scroll Saw Pattern Designer - 1183 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 80 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- As The Lathe Turns - 67 parts
- Workshop Development - 65 parts
- Sheila Landry (scrollgirl) - 1205 entries
- frank - 417 entries
- degoose - 387 entries
- dbhost - 331 entries
- Ecocandle - 325 entries
- MsDebbieP - 299 entries
- Martin Sojka - 297 entries
- Karson - 292 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- Gary Fixler - 204 entries
- mafe - 201 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- BritBoxmaker - 159 entries
- shipwright - 159 entries
- scottb - 144 entries