Sometime over a month ago I had one of those “I wonder…” kind of moments. I’d been wearing a Wavy Zebrawood ring that was finished with natural oil, giving it a very low-lustre appearance. The only way I could tell where the seam was located was by a small shiny area on the ring, where a small bit of cyanoacrylate adhesive remained. Normally my rings are poly-finished, and the tiny amount of squeeze-out glue at the seams is invisible. But due to the way this na...
Veneering, a Primer Course The top photo is a couple sample packs of sequenced matched veneers from Woodcraft supply.The secong photo is bookmatched Camphor veneer.The third photo is Bruce holding a sample of Avodire Crotch veneer, with No Finish on it. Some of you may have noticed my slight addiction to working with veneers. When you start to investigate the available veneers on the market, it becomes very difficult for me to understand the resistance to it that some people have....
Had a slight mishap today when I went to mill the legs down so they'd be the proper width after applying a "veneer" edge, I accidentally cut all the pieces! I should have left the those at the final width, I got a little carried away. A little creative thinking and milling a few more pieces out of the remaining door stock, and I'll have legs that will ultimately be a mere 3/16ths skinnier, but and I'm able to proceed using only this reclaimed door lumber. I've thought the inspiration ...
I’m building an 18” V-Drum Sander from http://www.stockroomsupply.com/V_Drum_Sander.php Stockroom Supply. I was given a Particle Board piece to use as a top it’s laminated with a thin slick veneer top and bottom. I’d like to band the edges with Oak that I already cut and mitered. The question is how to attach the Oak to the Particle Board edges? I’m read plenty of horror stories about splitting the Particle Board when using screws and/or nails to attach it. ...
The process continues… Glued it up tonight. I’m glad I could find the generic epoxy syringe at the local big box. I didn’t have time for a trek to Rockler or Woodcraft for a small glue kit. The tip fit perfectly between the fingers and was easy to control the amout of glue dispensed. I’ll be cleaning up the slightly proud ends of the joints tomorrow evening. I hope that goes well considering the fingers are only 1/8” thick. I’m a little worried about tea...
Under Pressure I don’t know about the rest of you, but glue up stresses me out. Even though we had dry fit the doors, I feel that time crunch as soon as I spread the glue. These doors are only held together by tiny tenons on the left and right beadboard pieces. The process Set out the clamps and separate the breadboard end to expose the tenons. Glue the tenons of the outer beadboard Clamp it Check for square by measuring across the diagonals Apply diagonal pressure if n...
Over the summer, I finally decided to tackle the jungle/mosquito breeding ground behind my back fence that I inherited from the previous owners. About halfway through, one of the nice wood handles (oak I think) on my loppers snapped: So being the good aspiring woodworker that I am, I glue them back together with basic yellow glue. A few weeks later I go back to finish up and the handle snaps again. This time though it snapped in a different place. Same handle, but the previous glue joi...
Hello All, Here’s a couple of photo’s on the upcoming Ferris-Wheel Feeder for the Squirrels. This set of eight seats will be attached to a rotating ring with hangers for the seats to rotate around. The idea is once the squirrel gets on then they will rotate to the bottom. If they climb up the seats then they’ll continue to rotate down to the bottom of the revolving wheel. The size of the seats are approx. 6 1/2, 2 1/2, by 1/14they are made of some small pieces o...
Thanks Everyone for the warm welcome everyone! I just a young guy that is a beginning woodworker. So if anyone has any tips and suggestions let me know!! The project that I am working on now is a wooden tub. I am using 8/4 red oak and building what is essentially big square box. Right now I am glueing up the wood together to make all the sides. Now I know what your thinking. Wood and water don’t mix. In the past when people have built wooden tubs it was left completely fi...
I was putting the finishing touch on my new workbench top the other night with a coat of wax. While I was at it, I figured I could also wax a few other things, like my miter saw top, router bases, etc. I also remembered a tip I read somewhere that said if you wax the bars of your clamps, glue won’t stick as much and will be easy to remove. Although that seems to be true, I discovered that if you wax the bars of clamps that work by friction (such as my multitude of the 6” Irwi...
1 2
15 entries
| Author | Latest activity | New comments or replies since you last checked |
||||
|---|---|---|---|---|---|---|
|
Cabinet Refacing |
MDRoehl | 59 seconds ago | by gmerteng | sign in to use this feature | |
|
|
World's Smallest Vase |
interpim | 1 minute ago | by Jim Jakosh | sign in to use this feature | |
|
|
Inlaws Bathroom Cabinets |
MDRoehl | 3 minutes ago | by gmerteng | sign in to use this feature | |
|
|
My Bathroom Cabinets |
MDRoehl | 8 minutes ago | by gmerteng | sign in to use this feature | |
|
Rockler 6" ruler on sale |
Dusty56 | 8 minutes ago | by Andrew | sign in to use this feature | |
|
|
Scraper planes |
gmerteng | 12 minutes ago | by gmerteng | sign in to use this feature | |
|
|
Woodshop cabinet rebuild |
ken90712 | 12 minutes ago | by Scott Bryan | sign in to use this feature | |
|
|
Excelsior 5-Speed Mini Lathe |
BlankMan | 13 minutes ago | by WoodSparky | sign in to use this feature | |
|
|
Jewelry box |
houseofwiens | 23 minutes ago | by webwood | sign in to use this feature | |
|
After Thanksgiving |
David Murray | 30 minutes ago | by Scott Bryan | sign in to use this feature | |
©2005-2008 LumberJocks.com. All Rights Reserved.
DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.
| Latest Projects | Latest Blog Entries | Latest Forum Topics 
|
Latest Projects | Latest Blog Entries | Latest Forum Topics 
|
