LumberJocks

Woodworking blog entries tagged with 'glue up'

  • Advertise with us
View Angela's profile

TV Stand #7: Cauls, jigs, molding and doors

09-15-2011 05:20 AM by Angela | 4 comments »

Bottom MoldingI cut a long piece of the African mahogany 3” wide. I original use ¾” but didn’t like the way it looked so I planed it down to 5/8”. I ran it through my router table using a Freud Roman Ogee router bit # 38362. I first cut the front piece. I used the same angles that I used on the main case. After cutting the side angles, the pieces didn’t fit based on the angles I cut them. When I glued the sides of the main case together the angles came out different from wha...

Read this entry »


View BritBoxmaker's profile

The Impossible #6: Its high time, Cymbaline

06-17-2010 06:16 PM by BritBoxmaker | 31 comments »

You are not going to believe how simple this glue-up is going to be. Some of you will not believe it will work. Others, possibly some of the cutting board purists, will say I’m cheating. Frankly Scarlet I don’t give a damn (name that movie). This is a box top and all its joints don’t have to be impervious to water, like a cutting board. I will flood the top of the pattern with a clear epoxy finish ultimately, anyhow. These are the players in this little drama. Left, t...

Read this entry »


View BritBoxmaker's profile

The Impossible #3: MI-2

06-12-2010 05:29 PM by BritBoxmaker | 29 comments »

Hello back again. I really don’t like glue-ups with pieces that have angles other than 90°. Strange really considering I make boxes with mitred joints. No matter, first question. Who can spot something missing from this picture This is how I found the workbench this morning. I could have sworn (and I do, a lot) that I had cut five 30mm pieces of Sycamore and theres only four there. In devon we have a special brand of pixie, called the f**kup pixie. They had obviously been in, ove...

Read this entry »


View twobyfour16's profile

Workbench #5: Trestle Base Complete

04-29-2012 05:56 PM by twobyfour16 | 7 comments »

Time to glue up. Since I painstakingly fit each tenon to it’s matching mortise, I was fairly confident that glue-up would go ok. To solve the short clamp issue, I went down to the hardware store & got some couplers to hook pipes together to get more length out of my pipe clamps. Also, I borrowed some longer parallel clamps from a friend – and I’m glad he had them! I did a dry assembly & everything worked great. It was a little tricky to do by myself, but I g...

Read this entry »


View clieb91's profile

Cheap Tricks #1: Glue Spreaders

05-31-2010 07:29 PM by clieb91 | 13 comments »

So I know everyone out there has some of their own money saving tips and tricks. I thought I would try to share a few of the ones I use. This idea came to me today while wandering around one of my favorite stores, trying to find items to put in my discount shopping bag. I saw a package of plastic glue spreaders for sale for $3.50 (per 6), I have read of guys using old credit cards and such and I have a few of them in my box but the items I found that seems to work well serves two purposes ...

Read this entry »


View BritBoxmaker's profile

Snakes Pattern in Solid Wood #4: The Union of the Snake

06-02-2010 05:51 PM by BritBoxmaker | 16 comments »

Well part of it anyway. A new set of eight clamping sticks, waxed this time and polished. Major squeeky bum (ass) time. Glue in a dish. Brush at the ready. Quick slurp of tea and there off…...........Pick up the piece, slap on the glue, position it in the frame. Repeat until you’re sure you’ve done something wrong. Put it right. Continue…...... After 20 minutes—->The glue was probably OK for another two rows but I bottled it (chickened out). Wasn’t used to ...

Read this entry »


View Sawdustonmyshoulder's profile

Conference Table for Local Church #7: Got a Really BIG Panel out in the Shop!

07-21-2008 06:17 AM by Sawdustonmyshoulder | 8 comments »

Sunday evening and it’s time to blog about the weekend in the shop. First on the agenda was to move the big tools around to make room to make a 54” by 144” table top in a two-car garage. Went to the blue box store and picked up a couple of 2×6 x 12’s and three sheets of 5/8 particleboard. I extended my workbench to be 4 foot by 12 foot. Works great! I took all of the 1×12’s out of the dinning room and straightened and made both edges paralle...

Read this entry »


View SoCalDJ's profile

Speaker Stands #1: Day 1

07-24-2011 08:04 AM by SoCalDJ | 2 comments »

Well today I started the project. I needed to make some speaker stands for my surround channels. I thought the options online were either stupidly expensive ($500 for some 4/4 Walnut really stands, Really?) or just ugly so I decided to make my own. I took inspiration from our new couch and used the baseball stitching in the leather to create design with contrasting walnut and maple. Today I spent the day milling the lumber (Just got a new old jointer :), Bridgewood 6”) and ...

Read this entry »


View Kyle's profile

Sweet Chest of Drawers Build #12: All Glued Up and onto the Drawer Fronts

07-30-2013 09:53 PM by Kyle | 2 comments »

This past weekend I did a pretty massive and ridiculously stressful glue up. It wasn’t as bad as I’m making it sound but with how long I’ve been working on this chest of drawers, I just wanted it to come out square and solid. I’m pleased to announce that I was successful. Because of the magnitude of this glue-up, I didn’t bother taking any pictures. The biggest part was gluing the outer frame with the panels in place, and then while all of that was safely clamped...

Read this entry »


View MolokMot's profile

Cutting Boards #4: Final Glue-Up and Flattening

03-30-2012 02:18 PM by MolokMot | 2 comments »

After the last glue-up, and flattening the panel, I cross cut the panel in strips 1.25” wide. Taking those strips I turned them so the end grain was showing and flipped every other one end for end to create the checkerboard pattern. I am sure we have all seen Marc Spag's (aka: TheWoodWhisperer) video. (7 – How to Make a Butcher Block End Grain Cutting Board) I am sure Marc loves all of the extra attention on the subject of cutting boards. Glue up was somewhat frustrating because I...

Read this entry »


« prev 1 2 3 4 5 next »
49 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com