LumberJocks

Woodworking blog entries tagged with 'glue up'

  • Advertise with us
View BritBoxmaker's profile

The Impossible #6: Its high time, Cymbaline

06-17-2010 06:16 PM by BritBoxmaker | 31 comments »

You are not going to believe how simple this glue-up is going to be. Some of you will not believe it will work. Others, possibly some of the cutting board purists, will say I’m cheating. Frankly Scarlet I don’t give a damn (name that movie). This is a box top and all its joints don’t have to be impervious to water, like a cutting board. I will flood the top of the pattern with a clear epoxy finish ultimately, anyhow. These are the players in this little drama. Left, t...

Read this entry »


View BritBoxmaker's profile

The Impossible #3: MI-2

06-12-2010 05:29 PM by BritBoxmaker | 29 comments »

Hello back again. I really don’t like glue-ups with pieces that have angles other than 90°. Strange really considering I make boxes with mitred joints. No matter, first question. Who can spot something missing from this picture This is how I found the workbench this morning. I could have sworn (and I do, a lot) that I had cut five 30mm pieces of Sycamore and theres only four there. In devon we have a special brand of pixie, called the f**kup pixie. They had obviously been in, ove...

Read this entry »


View degoose's profile

Weave pattern LL Dip and Chip #2: Cutting and Gluing up the weave.

06-03-2010 12:13 PM by degoose | 29 comments »

Here is the cutting and dry fit of the weave pattern…I sanded the lengths on the Jet 16/32 drum sander and cut the individual piece to length using an Incra Mirtre Express..You can see the Magswitch Magnets I am using as stop blocks… one long and one short…The pieces are kept in order they are cut so that the grain orientation is maintained… this makes the illusion…Enjoy the slide show of the actual glue up…Martyn… start to finish for the glue up̷...

Read this entry »


View RGtools's profile

Progress of a self taught cabinet maker #14: A quick safety tip.

08-07-2012 12:12 AM by RGtools | 25 comments »

When using a striking block to assemble joinery. Make sure to use a block that you can grip from the sides and not from the top. The below image is the “don’t” picture. This of course happened in the beginning of the below glue up…as if I needed it to be more interesting. Hope your next glue up goes well. Ryan

Read this entry »


View RGtools's profile

Occasional Table Class (Hand Tool Build) #24: Drawbore, Glue Up, and Starting on the Tabletop

03-11-2012 10:44 PM by RGtools | 22 comments »

The process of drawboring has been mostly covered but I felt like giving a few tips in case this is in your mind to do on your table. The main thing is to make sure that the holes are spaced so they miss each other and are close to the middle of the tenon (mine could have been closer). Also make sure that the hole you drill is not going to be under the shoulder of one of your rails…simple mistake that makes assembly kind of hard. Your holes should be as close to the rails as they can be witho...

Read this entry »


View dustbunny's profile

"Don't Stress" glue ups

06-04-2010 02:55 AM by dustbunny | 21 comments »

I got so tired of fighting with glueing up cutting boards.Is everything lining up ? Is there slipping ? One clamp at a time !!So I spotted these flooring jacks in the HF catalog...and I began to wonder.I bet that I could use these to clamp cutting boards together in hopefully one shot.I haven’t tried it yet, but I will let everyone know if there are problems.I am thinking this is going to work just fine.I may need to add regular clamps at the corners, we’ll see. I did h...

Read this entry »


View Todd A. Clippinger's profile

Cat Scratch Fever

12-25-2009 07:17 AM by Todd A. Clippinger | 19 comments »

The Mission I was contacted by some clients and asked if I would take a look a repairing an antique table they had. Antique may be used loosely here but it was an old table and was part of a set of nesting tables. The set may not be of any particular value as antiques, but the clients hold a certain fondness for the tables and wanted to see if it could be repaired. I arrived to their loft apartment, greetings were exchanged, and I was given a brief introduction to the project. The top h...

Read this entry »


View Gary Fixler's profile

found wood #16: Cora's Mexican restaurant wood

03-28-2010 07:22 AM by Gary Fixler | 17 comments »

Cora’s, a local Mexican restaurant went out of business recently. On my way back from the bearing shop with the new bits for my planer this past week I noticed a crew tearing the insides out. I stopped in and asked if I could look through their scrap pile for free wood, and as happens pretty much always here in west LA, they looked at me, shrugged their shoulders, and said “sure.” There’s wasn’t much, and nothing great, but the wood looked old, and I t...

Read this entry »


View BritBoxmaker's profile

Snakes Pattern in Solid Wood #4: The Union of the Snake

06-02-2010 05:51 PM by BritBoxmaker | 16 comments »

Well part of it anyway. A new set of eight clamping sticks, waxed this time and polished. Major squeeky bum (ass) time. Glue in a dish. Brush at the ready. Quick slurp of tea and there off…...........Pick up the piece, slap on the glue, position it in the frame. Repeat until you’re sure you’ve done something wrong. Put it right. Continue…...... After 20 minutes—->The glue was probably OK for another two rows but I bottled it (chickened out). Wasn’t used to ...

Read this entry »


View Ecocandle's profile

Extremely Average #29: Henry Wood Detective Agency

01-31-2010 05:31 AM by Ecocandle | 14 comments »

Henry’s head was still throbbing from ringing in the New Year. He looked at his calendar, a present from his brother in Manhattan, a New York Giants fan of all things. The calendar had a team picture of The World Series Champion Giants, who swept the Cleveland Indians in 4 games. It was galling for him to look at and he mumbled to himself, “At least the damn Yankees didn’t win their 6th in a row.” For though Henry didn’t care for the Giants, the previous two years had seen his beloved...

Read this entry »


1 2 3 4 next »
37 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase