LumberJocks

Woodworking blog entries tagged with 'frame'

  • Advertise with us
View Woodhacker's profile

Walnut Coffee Table Construction

05-11-2008 02:16 AM by Woodhacker | 13 comments »

When I returned to woodworking several years ago my nephew had been talking about a particular style of “coffee” table he’d seen online somewhere and was describing it to me. Since he’d just announced plans to marry, I told him I’d make him, and his fiancée, the table as a wedding gift. He showed me some online photos of the table, which I used as the basic, general design plan. The joinery I chose is original but the style was taken from the photos. This piece is the result: ...

Read this entry »


View Woodhacker's profile

Radial Dovetail Box Construction

10-18-2008 11:15 PM by Woodhacker | 17 comments »

Some time ago I posted a blog about a dovetail joint I came up with. I call it the radial dovetail. It incorporates handcut dovetails, but rather than using the traditional 1:8 ratio for the dovetail angle for hardwood, each side of each tail varies and is drawn from a perspective point. Then the sides of the box were contoured to blend with the dovetail design. Here’s a picture of the nearly completed box. It is made of curly maple, Carribean rosewood, and hickory.I like to think of t...

Read this entry »


View John Nixon's profile

Flag and Certificate Display Case

05-24-2008 03:09 PM by John Nixon | 6 comments »

Just in time for Memorial day… I made a display case for my father-in-law that holds an American flag and certificate. The flag and certificate were presented to him by an active Navy Seal serving in Operation Iraqi Freedom. The certificate shows the date the flag was flown over Camp Patton in Fallujah. This was quite an honor for my father-in-law, and the flag and certificate deserved a special case to preserve and protect them. Here’s a link to the video on how the ca...

Read this entry »


View Sgt_Lobo's profile

Trinket/Shadow Box (Iraq Display) #1: One of the main reasons I joined LJ...

11-06-2007 05:45 AM by Sgt_Lobo | 17 comments »

Well, here it goes…the long story. On my last tour to Iraq I was stationed at Balad AB, the largest FOB (Forward Operating Base) in the AOR (Area of Responsibility). I was in charge of a 110 person security team known as the FPs (Force Protection). To make a long military story short (since this is a woodworking site, not a military site), my team was responsible for the security of the entire base both inside and outside the wire, and a lot of stuff happened that made us a very tigh...

Read this entry »


View Sheila Landry (scrollgirl)'s profile

My Journey As A Scroll Saw Pattern Designer #6: Self-Framing Picture Frame Finished

06-08-2010 02:08 PM by Sheila Landry (scrollgirl) | 7 comments »

Yesterday turned out to be a pretty productive day. Among other things, I finished cutting my matching self-framing picture frame, which will be the companion piece to the dresser tray I designed last week. In designing this pattern, I was fighting with whether I should or should not do additional scroll work in the center of the tray. To me it seemed that it was interesting enough on its own. I wanted the scroll work border to be the highlight of the piece, along with the beautiful chara...

Read this entry »


View MsDebbieP's profile

LJ Gateways #2: Gateways to Projects

01-18-2011 02:21 PM by MsDebbieP | 15 comments »

The following are gateways to project/blog/forum postings re: the identified topic(more coming soon)     LumberJocks’ Projects/Skills Gateways Bandsaw Boxes Benches Birdhouses Bookshelves Bowls Candle Holders Canes Clocks Coffee Tables Cradles Decks Doors Entertainment Centres Frames Guitars Hinges Jigs Kids' Projects Pen-Making Planes Sanding/Sand Paper Scrollsaws Toys All LumberJocks’ GATEWAYS Safety Tips ...

Read this entry »


View PurpLev's profile

Router Table #5: Half Throttle - Cabinet is Framed!

12-26-2009 04:20 AM by PurpLev | 16 comments »

I picked up today where I left yesterday. today however, I had a bit more time to work on this. I printed the face frame design/layout from Sketchup, and out to the freezer we go: I added the 2nd piece that makes up the back (had to use 2 pieces of plywood as I don’t have 1 large enough part for the back), and then I noticed that my plywood carcass is a bit out of wack- the back aligns with the left side, but the right side is a bit lower, ah crap, I guess I’ll have to shim...

Read this entry »


View PurpLev's profile

Frame Saw Build #3: Template me this, Curve me that.

10-24-2011 08:25 PM by PurpLev | 14 comments »

Using my previously made SketchUp model I made a full sizes printed template using the following steps: 1. Setting up a Parallel view: The default view in SketchUp is “Perspective” which allows us to view things in 3D which looks ‘real’ due to the perspective view but for printing we want to be able to see the drawings in 2-D as if they were printed on a flat paper (which is what we about to do). In order to do this you need to go to the menus under “Camera...

Read this entry »


View mafe's profile

Simple picture frame DIY BLOG (gift for friend)

12-20-2010 07:41 PM by mafe | 7 comments »

Simple picture frame DIYA birthday gift for my best and most loyal friend during 20 years now My wonderful old friend Michael, had a birthday, and I was planning to buy him a meditation, self insight or perhaps; man in the in the midway crisis book. Yes we are both around the tricky 40. I was looking out the window, trying to come up with a good idea. But my wonderful Caroline said to me on Skype ‘why don’t you give him something personal’, and I agreed right away. ...

Read this entry »


View chopnhack's profile

Mobile Workstation #1: The center of my shop renovation - from the ground up..

03-04-2012 07:07 PM by chopnhack | 6 comments »

The mobile workstation is in my opinion going to be the center of my workshop once its built. An integrated router table, table saw, downdraft table and ample storage in a ~ 5’ x 2’ area on wheels! Certainly not my idea, however, the layout will be done solely by me. I am open to all suggestions though, so please feel free to brainstorm here and let me know what has worked for you, what you would do differently if you had to build one again, etc. All comments and suggestions are w...

Read this entry »


1 2 3 4 5 next »
48 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com

Latest Projects | Latest Blog Entries | Latest Forum Topics

GardenTenders.com :: gardening showcase