So I thought I’d have a go at sharpening the 14 inch Cowell & Chapman backsaw (which is really a W. Tyzack, Sons & Turner). I’m going to file it 10.5 TPI rip with 9 degrees of rake and 5 degrees of fleam. I was going to add 5 degrees of slope as well, but I figure at this point I should just concentrate on filing the fleam correctly without complicating things further. Remember this one? This saw has an extra-heavy brass back and therefore there is a considerable am...
A few more photo’s in the handle re-modelling saga. A bit more ‘Fettling and Fiddling’, re-shaping the lamb’s tongue- A bit more filing and sanding Wetting the surface with water to raise the grain- When dry more fine sanding and out with the Danish Oil Now all I need is to sort the sawplate out! Before Photo- The original scruffy handlle… ...and after
Next up on my epic backsaw journey is a much younger saw (60s, 70s? – not sure exactly). It’s a W. Tyzack, Sons & Turner filed 10 TPI crosscut and sports an extra heavy brass back. I bought this saw because it was cheap and there was nothing wrong with the saw plate. Gone is the subtle stamp that appeared on the brass back of a 19th century Tyzack saw. Instead, this spine has a rather garish impression. The crisp elephant logo now looks like a partially thawed out woolly mam...
The Humble Hand Brace - A Beginner's Guide to Restoring, Buying and Using #2: Part 2 – Cleaning and Restoring a Brace to ‘Like New’ Condition
At the end of Part 1 I showed you a photo of the polished chuck. The outside was complete and the rust had been removed from the inside, but I still had to smooth the inside face to prevent it marking the jaws again. To do this, I cut a piece of dowel about 4” long, and marked approximately 1 1/6” in from one end using an awl. Then I drilled a 3mm hole using a hand drill. Well who’s got time to charge batteries these days? Using my dovetail saw, I cut a slot about 1/16” wide str...
Didn’t find any related content so thought I’d throw this out.I keep a lot of my tools and hardware (o.k. and old magazine issues, and reference books, and sandpaper, and…well you get it) in filing cabinets.I don’t use the cheap ones, if they aren’t commercial grade, full extension, heavy duty slides I won’t get them.I don’t pay retail, it seems the new paperless business has a lot of companies getting rid of thiers. I get them at thrift stores, garag...
Last week I blogged about making a marking knife from scratch. I had gotten as far as getting a good start on the handle and filing the blade to a point. Yesterday, I was going to file a bevel onto the blade, hone it, and then work on getting in mounted in the handle. I didn’t quite get that far. Do you know how hard it is to hand-file bevels onto a spear-pointed knife, so that both sides are even? I found myself overdoing one side, then the other. I made adjustments to the angle ...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 246 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries