LumberJocks

Woodworking blog entries tagged with 'fence'

  • Advertise with us
View mafe's profile

Deep stop for a Record 50 / 43 ( Stanley) BLOG.

05-23-2010 08:03 PM by mafe | 12 comments »

Hi all…Here I am again, have some time since I’m in Paris visiting my fionce who is French. Deep stop for Record No. 43 / 50 plane (Stanley)Perhaps a smiths project… (at least silver smith).Here are also a blog of how to make wooden fence: http://lumberjocks.com/mafe/blog/15855 Ok I admit! It was not clever of me, I did not see that the deep stop was missing on the 43 I bought on E-bay. But the seller was nice and gave me a 4 pound discount on a price that was 13, so I was s...

Read this entry »


View mafe's profile

Wooden fence, and tuning up a Record No. 50 plane (Stanley) BLOG.

05-22-2010 03:16 AM by mafe | 5 comments »

Hi guys and girls of course… Wooden fence, and tuning up a Record No. 50 plane (Stanley)A little tuning up on one my no. 50 planes (I have 2 now).Here are also a blog of how to make a new deep stop: http://lumberjocks.com/mafe/blog/15882 Why put a wooden fence?Because it’s more gentle against the wood you are going to plane, and with a high fence like this, you can also hold a good 90 degree angel against the wood. You can make also a low one, that just holds the hight of th...

Read this entry »


View Gary Fixler's profile

tragedies #11: the back yard fence saga

03-26-2010 09:51 AM by Gary Fixler | 7 comments »

It sure feels like everything is falling apart this year. There was the planer and its bearings. Too, more than ever I’m wearing out shoes and clothes. I’ve gotten wood glue or finishes on and holes in so many shirts now, and had 3 pairs of jeans become for lack of a better word ‘dry rotten,’ each ending up with tears more than a foot long. The dryer broke… again (washer broke last year – the bottom rusted out and after filling, it popped and dumped water a...

Read this entry »


View captkerk's profile

The Great Garage Reorganization and Shop Improvement Act #3: New Table Saw

02-11-2010 12:45 AM by captkerk | 10 comments »

Any good workshop redo includes new tools and I finally replaced my old Craftsman bench-top saw with a Ridgid R4511. I got it for the clearance price of $499, but then three days later it dropped in price to $299. I was able to get Home Depot to honor the new lower price and I came away with a brand new saw for an almost criminally low price. The assembly was a bit time consuming, but the other lumberjocks’ reviews helped with some of the common issues. I was quite annoyed to ...

Read this entry »


View PurpLev's profile

Router Table #12: The Good the Bad and the Ugly... New Fence Arrived

01-31-2010 02:07 AM by PurpLev | 22 comments »

I saw an ad on craigslist for a Jointech 12” router fence positioner which is similar to the Incra LS positioner -has a lead screw, and has what Incra sells as add on – the “wonder fence” as the standard fence. the guy posted it as used, but at what Jointech is selling it NEW… I contacted the person trying to negotiate a win-win situation. that was 2 weeks ago. the jointech fence is still on craigslist. I just couldn’t justify his price for a fence I’...

Read this entry »


View PurpLev's profile

Sketchup Resources #5: Incra 17" LS Positioner System

01-26-2010 04:28 PM by PurpLev | 10 comments »

Finally got the fence and was able to model it out last night. I wish I had the opportunity to do this earlier, or at least have this model before I cut the hole in my router table top for the router plate as based on this fence I would have liked to put it 2.5” more to the front. but. 2.5” is not that critical, and I could move the fence backwards if needed. hope this can help someone else: this is not a production model, but just a model to help visualize and design a ro...

Read this entry »


View DannyBoy's profile

My Shop #2: Table Saw Fence

10-29-2009 10:02 PM by DannyBoy | 5 comments »

To continue the series of setting up my Craftsman table saw, I’d like to go over adding the aftermarket Delta T2 fence system. I have basically followed the same steps as Jamie did on his setup. For the most part, this is the way to go for this setup. A couple of things before I get started. First, you will have to drill new holes in the mounting brackets for the fence system. There is no way around this. If you take your time and pay attention, you’ll do alright. Second,...

Read this entry »


View kolwdwrkr's profile

Fence #2: Completed back section

08-09-2009 07:20 PM by kolwdwrkr | 2 comments »

Well the street side of the property is completely fenced off. I think it came out good for not being a fence maker. Now I need to do a gate, a small side yard section and another entire length up against the neighbors yard (my foreclosed home :^( ). That section needs to be designed differently and won’t have the lattice for privacy issues. It will also be taller. ~71”. 72” requires a permit. Suckers. LOL. It will be coming off of the section I already did, so I am go...

Read this entry »


View JoshO's profile

Fence upgrades #1: Installing my new Delta T2-30 on a Craftsman flexdrive.

07-20-2009 02:34 PM by JoshO | 2 comments »

It all started with dissatisfaction with my Craftsman Flexdrive table saw. It was difficult to make a decent cut with the saw. I understood part of the problem could have been lack of experience on how to use the tool, but it wasn’t exactly a complicate piece of equipment and degree in rocket science wasn’t necessary. After doing some research, I came across an interesting post that taught me that a table saw is nothing more than table with blade mounted underneath it. All the mag...

Read this entry »


View sIKE's profile

Norms Router Cabinet #8: and Finally the Fence

04-09-2009 07:56 PM by sIKE | 10 comments »

I have had the cabinet completed for sometime now, and had the Incra Fence already. However it is not a general purpose fence, one that you can attach feather boards and such to. I need to be able to keep my work flat on the table for my current project (Sliding Dovetails) so I am now having to build this guy out. Having read about the complaints about the MDF swelling after a period of time I have decided to finish mine out with paint. I went to the BORG and grabbed a can of a off white spr...

Read this entry »


« prev 1 2 3 4 5 6 7 next »
62 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com