Woodworking blog entries tagged with 'easy wood tools'

  • Advertise with us
View Sawdustonmyshoulder's profile

Delta 46-715 Lathe Refurbish Project #7: Controls Done and Turning Zinc!!

01-20-2015 04:02 AM by Sawdustonmyshoulder | 8 comments »

The control box is done and mounted. I found a few things out the hard way. One was you don’t ground the motor controller. Man, the flash and the smoke! Well, that was a motor controller down the drain. Luckily, I had a spare. Upon a little research, DON’T GROUND THE MOTOR CONTROLLER’S HEAT SINK. The box I bought was aluminum, so I had to isolate the motor controller from the box. Nylon screws, washers and bolts was the solution to the grounding issue. I did ground the alumi...

Read this entry »

View McLeanVA's profile

Easy Wood Tool Replaceable Cutter Heads

12-04-2012 08:37 PM by McLeanVA | 7 comments »

I am a huge fan of the Easy Wood Tool series and have really enjoyed using my full size Ci1 Rougher and Ci0 Finisher on spindle and faceplate projects. I guess the only real gripe is that the EWT cutter heads (while you never need to sharpen them) cost just under $20 each. So, I did some measuring with the calipers and some good old Google legwork and found that Byrd Tool makes a cutter head that is near identical to the EWT version at a fraction of the cost ($2.80 each). I’m sure...

Read this entry »

View Sawdustonmyshoulder's profile

Easy Wood Tools / Midi Lathe Duplicator #1: Making the 'Stands'

02-01-2015 11:46 PM by Sawdustonmyshoulder | 5 comments »

As they say, ‘Necessity is the Mother of Invention’ and you, the woodworker, knows that fact the best. I have a little job where I am going to make 4 finials for a mahogany antique bed. I tried to buy some pre-made finials online but I couldn’t find any that matched the size and the style. Besides, the finials I found were maple and I just don’t want to try to match the finish already in the hole of trying to make maple look like mahogany. I have a set of Easy Wo...

Read this entry »

View Sawdustonmyshoulder's profile

Easy Wood Tools / Midi Lathe Duplicator #2: Turned the Finials.

02-08-2015 09:11 PM by Sawdustonmyshoulder | 3 comments »

Developed the method of attaching the template to the base. Simple 1/4” dowels in holes in base and template. Using the tools on stands, I turned the finials. I did use my other lathe to rough out the blanks to round, cut a tenon for the chuck, rough in the square shoulders using a parting tool, and rough out some of the waste with a roughing gouge. I did use the tailstock for safety when turning using the duplicator. I sanded the finials to 220 grit and trimmed off the to...

Read this entry »

View Sawdustonmyshoulder's profile

Easy Wood Tools / Midi Lathe Duplicator #3: Final Testing and Some Adjustments

02-20-2015 01:29 AM by Sawdustonmyshoulder | 0 comments »

I found in my testing that I need to offset the EWT Finisher from the blank about 1/16 inch. I made a new ‘follower’ using a 1/2 inch washer. This washer offset the cutter all the way around. Using the EWT Detailer that is set to cut equal to the pattern, I make the final pass on the finial. Here are some images of the testing on a finial project. Check out my blog on a great finishing helper using a DVD container. I also have a project with a step by step ...

Read this entry »

DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics