LumberJocks

Woodworking blog entries tagged with 'easy'

  • Advertise with us
View ShaunMeighan's profile

Making a Sign from a Cutting Board

04-29-2016 05:50 PM by ShaunMeighan | 0 comments »

https://youtu.be/fPf5VXlwekQ Hi there folks! Just thought I’d share with you all my latest project, where I make a sign for my workshop out of an old cutting board. The finished piece is not perfect, but neither is my woodworking!! Hope you enjoy!

Read this entry »


View A Slice of Wood Workshop's profile

Really Simple Outdoor Table-Pt 1

04-01-2016 08:14 PM by A Slice of Wood Workshop | 1 comment »

Easy made side table for a porch or just to sit next to some chairs. Next is the mortises and finishing.

Read this entry »


View JetDriver's profile

Musings of an Amateur - Building a Sewing Table #1: Getting Started on the Legs and the Frame

02-18-2016 05:44 PM by JetDriver | 1 comment »

My wife recently purchased a sewing machine and in the run up to that we were trying to figure out a sewing table for her. The idea was to keep it cheap but as she’s on the shorter side and finds many standard tables a bit uncomfortable we wanted something that fit her frame. We looked at various ideas and Ikea Hacks but ultimately decided on taking and idea for a farmhouse table and modifying it into a sewing table for her. The table will be 70”x24” when done and 27̶...

Read this entry »


View ThomasLightle's profile

Dust Collection #3: Simple, Cheap, and Easy Blast Gates

01-16-2016 09:56 PM by ThomasLightle | 1 comment »

Sometimes motivation behind building something as opposed to buying has to do with availability. Sometimes it has to do with cost. Sometimes it has to do with quality. In this case it has to do with all three. I set out to build blast gates with scrap material I had laying around. Mainly I did this because I didn’t want to have to order blast gates and deal with the shipping, and the cheap ones seemed a little….flimsy? There are high quality ones out there, but why pay for th...

Read this entry »


View casecx700's profile

First attempt at making a carbide tipped lathe tool

08-11-2015 05:08 PM by casecx700 | 2 comments »

This is my first attempt at making a carbide tipped lathe tool, the handle is made of oak and ash cut and glued at a 45 degree angle and doweled for added strength. The metal part that holds the cutter is made of a piece of .5 inch round rod that I purchased from home depot and tapped a #8 32TPI thread into to accommodate the easy wood tool cutter. Currently I am waiting on the epoxy to set up so I can finish it up tomorrow hopefully. I am planning on finishing with Boiled linseed oil.

Read this entry »


View Kaleb670's profile

final project #1: Still thinking

04-24-2015 02:34 PM by Kaleb670 | 1 comment »

So I need a easy project for my final project. Can you guys help me get a project to do. So I don’t fail. Thanks

Read this entry »


View Chris McDowell's profile

Last Second Christmas Project - Wooden Soap Dishes

12-23-2014 04:48 PM by Chris McDowell | 7 comments »

I made 10 wooden soap dishes for a relative. I used cedar from a scrap 4×4 post. These are easy to make as Christmas gifts or to sell at craft shows or on Etsy. I’ve seen people sell tons of these on Etsy for 4 or 5 bucks a piece. I would not recommend using cedar as it’s very brittle and very soft, which makes it almost impossible to make these without blemishes. I used poplar a couple of years ago and those have held up just fine. You have to cut the grooves so that ...

Read this entry »


View A Slice of Wood Workshop's profile

Easy DIY Scoops on a Bandsaw

12-14-2014 10:32 PM by A Slice of Wood Workshop | 1 comment »

With the arrival of my new bandaw, I figured it was time to try it out on a project. Thanks to Patricks Workshop on Youtube, I was able to have a fairly easy project to give it a test run. These bandsaw scoops are easy to create and would make nice gifts. Stop over and check out the video HERE and make sure to subscribe for woodworking and blacksmithing videos!

Read this entry »


View A Slice of Wood Workshop's profile

Twin Pipe Vise

07-20-2014 09:08 PM by A Slice of Wood Workshop | 1 comment »

I’m tired of seeing all these moxon vises and not making my own. They are pretty expensive. I really need something to act as a front vise on my bench. This takes care of that problem and it also raises any cutting that i’ll be doing by 7 1/2” (which helps out the back). Here is my version of the moxon vise using two pipe clamps. Check out the video. Please subscribe to my channel and check out all the other videos on there.

Read this entry »


View A Slice of Wood Workshop's profile

No Tail Vise? No Problem.

06-04-2014 09:38 PM by A Slice of Wood Workshop | 4 comments »

I go over two techniques to get around with not having a tail vise. If you have other ways, feel free to share them in the comments.

Read this entry »


1 2 3 4 next »
32 entries


DISCLAIMER: Any posts on LJ are posted by individuals acting in their own right and do not necessarily reflect the views of LJ. LJ will not be held liable for the actions of any user.

Latest Projects | Latest Blog Entries | Latest Forum Topics

HomeRefurbers.com