This article first appeared on my website, Lockwatcher's Lair – I am duplicating it here to share my experience using this system with my fellow Lumberjocks. While not specificly “woodworking” this system can speed up the process of reconditioning old tools without destroying them. The Rust Bucket Let me first thank my good friend Dave, of Pearce Woodworking for this great idea. Dave had some used hand tools he needed to clean up and had located this method th...
well unfortunately i will not be able to have the table saw station that i was hoping for but a router table is something i need so i am making one on the side of my table saw. i started by cutting down all the MDF with my cousin pat’s (Anthrax) help. then i started putting the torsion box together. it is all based on where the bolts are for my table saw and in the center fitted for the rockler plate that i am planning on getting in the future just i don’t have the money now. so h...
Thanks for joining in again and I apologize for the delay. Hand is doing a lot better and it feels great to be back in the shop. Thanks for your patience and your encouragement to get better. In this section we will focus on shaping and sanding our pieces. In my opinion, this is the most important part of the process. Depth is what makes a piece really stand out and the more depth you use in your project the better you’re going to like the end result. We have all seen intarsia pieces...
In the spirit of giving back to all you LJ’s who have inspired and informed me, here is an attempt to share the making of 4 tool bar handles. My wife gave me four 1/2” tool bars and 12 carbide cutters for Christmas from my wish list. Wanted to try some Easy Wood carbide type tools at a reasonable price level. To hold the cost down my wish list specified bars and cutters from Big Guy Productions and then turn my own handles for them. Step 1 – Turn HandlesThe project star...
Thanks for joining us for the third installment of “Intarsia Basics” and this is where it starts to get really fun. Cutting out the pattern is one of the best parts of doing this kind of art. It takes a little practice to get used to using your saw. You can look up some practice patterns or just make some zig zags, loop the loops, straight lines, gentle curves, and circles on a piece of paper and glue to a practice board. Cut out some of these and you will start getting used to the “feel ...
We recently purchased a new washer, & dryer, & we didn’t want to spend $400 for the factory pedestals, so I’m making my own. They should cost us about $75 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~This is the factory made pedestal~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~The front load machines are kind of low without a pedestal. It makes it kind of tough on the back muscles.~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~...
Here are the steps I used to make an obelisk incense burner. I selected a 3 1/2” square by 7” long piece of pretty wood. Box elder in this case. I made a drawing to scale and then had to plan the steps in the process so I did not get ahead of my self because it would be impossible to do some of the steps out of order. Being an incense burner it need air flow to keep the cone burning. I started with the top vent holes while the block was whole. 4 -3/16 holes on a 3/4”...
Here’s a video update on my steam bending project. Enjoy:
Hey Everyone! i know its been awhile but i finally have another episode of the Teenage Woodworker to put up! in this episode i talk about how i do mortise and tenons. so i hope that everyone likes it! So I hope that everyone likes the episode. i will have another one out sometime next week. I’m taking the T-Chisel challenge and making a step stool so i figure that i will document that. i have some cool things to show. especially the finish! so i hope that everyone liked it and...
Well, its been awhile now so i figured that it was time for another shop tour. i have made a lot of shop additions in the past few months and i have gone from just a kid with a few tools to this now having a fully funtional shop and being able to sell my work and taking in commissions. so here is my updated shop tour watch out it gets a little crazy at the end, but i left it in for giggles :) so i hope that everyone liked it. i’m really not sure what the next videos i am going t...
- My Journey As A Scroll Saw Pattern Designer - 1190 parts
- Extremely Average - 324 parts
- A journey into the workshop. - 87 parts
- Daily Update - 87 parts
- Just for Fun... - 81 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- The Craftsman's Path - 67 parts
- As The Lathe Turns - 67 parts
- Workshop Development - 65 parts
- Sheila Landry (scrollgirl) - 1212 entries
- frank - 417 entries
- degoose - 388 entries
- dbhost - 331 entries
- Ecocandle - 325 entries
- MsDebbieP - 300 entries
- Martin Sojka - 297 entries
- Karson - 293 entries
- William - 249 entries
- Betsy - 221 entries
- Stevinmarin - 212 entries
- mafe - 206 entries
- Gary Fixler - 204 entries
- Todd A. Clippinger - 187 entries
- Chris Davis - 183 entries
- Rustic - 183 entries
- PurpLev - 162 entries
- shipwright - 160 entries
- BritBoxmaker - 159 entries
- stefang - 145 entries