[Above] This was my last log of elm in which I hoped to find some more spalted wood. The first thing I did was to grab my Australian Bowie knife and strip off the bark. It came off very easily as the log (2 feet long, 4 inch diameter ) had been sitting on the ground under leaves for several years. [Above] Then I put the log in its most stable position on its side and attached a 1×4 to each flank, making sure it was fairly stable and trying to have the boards parallel to the b...
Today we tore down the south wall of the shop. My Dad, my (twin) brother and I started at 7am and finished and around 2pm. We started be removing the tin, the taking out studs and posts with chainsaws and sledge hammers. A scissor life made this much easier then using a ladder. There were four large wooden posts which were about 4 feet in the ground that were pulled out by a Deere 50D mini excavator. We also had to remove the existing garage door. The reason we took down this wall today is so...
Ok, so it’s much more fun to dance than to fix…. Apparently welding a frame should not be undertaken without proper support, or ahh… more experience. The frame had a twist to it across the 59.5” length! I cleared a section of the shop floor (miracle) got out my door installation level and found a fairly level area. I then proceeded to use some shims to adjust the floor until the it was perfectly level. Gotta give credit to the guys that screeded the floor some 50 y...
The mobile workstation is in my opinion going to be the center of my workshop once its built. An integrated router table, table saw, downdraft table and ample storage in a ~ 5’ x 2’ area on wheels! Certainly not my idea, however, the layout will be done solely by me. I am open to all suggestions though, so please feel free to brainstorm here and let me know what has worked for you, what you would do differently if you had to build one again, etc. All comments and suggestions are w...
It’s snowing here so Its out of the unheated shop and staying indoors – good time to make the blade clips. I chose to use stainless steel because I waned a material that won’t rust, be strong and capable of sustaining the blade tension, and I like the color (not a big fan of brass although I do like it as an accent in some cases). I ordered some 1/2” stainless steel rods from Speedymetals a while back for no real reason when I ordered some other material as it was o...
I’ve been planing to build a down-draft table for quite awhile. It’s probably as important as a dust collector for staying ahead of dust collection. Someone gave me a furnace blower that puts out a lot of air, and I’ve been planning and plotting. My big hangup has been that the filters will plug up fast and I’ll be cleaning them all the time. This weekend I cut up a bunch of MDF and was surprised to see quite a pile of MDF dust in my dust seperator. When the air an...
- My Journey As A Creative Designer - Woodworking and Beyond - 1742 parts
- Extremely Average - 324 parts
- Workshop Development - 107 parts
- A journey into the workshop. - 105 parts
- Just for Fun... - 97 parts
- Daily Update - 87 parts
- Life as an Amateur Woodworker - 79 parts
- "Hobbit Holes in MyWorld" --by RusticWoodArt - 77 parts
- As The Lathe Turns - 76 parts
- WoodWriting Haiku Thursday's --by RusticWoodArt - 74 parts
- Sheila Landry (scrollgirl) - 1767 entries
- dbhost - 418 entries
- frank - 417 entries
- degoose - 397 entries
- Ecocandle - 325 entries
- MsDebbieP - 314 entries
- Karson - 305 entries
- mafe - 304 entries
- Martin Sojka - 296 entries
- William - 258 entries
- shipwright - 245 entries
- Betsy - 228 entries
- stefang - 220 entries
- robscastle - 218 entries
- Dave Rutan - 213 entries
- Stevinmarin - 212 entries
- Todd A. Clippinger - 207 entries
- Gary Fixler - 204 entries
- Smitty_Cabinetshop - 193 entries
- A Slice of Wood Workshop - 190 entries